RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 770 views TOPIC CLOSED
HomeAircraftHelicopter
e-
Blade
Blade 400 › 3D Please help me setup my Blade 400 with new gyro and tail servo
01-18-2009 04:00 PM  9 years agoPost 1
MEL760

rrApprentice

Canton, Michigan-U.S.A.

My Posts: All  Forum  Topic

Hello everyone and thanks a million for stopping by and possibly taking a poke at this...
Stock blade 400 (cyclic hs65mg's on the way) but I just got my ds3400G tail servo and jr500t gyro installed. I had to go in my dx6i and reverse the rudder servo, made some adustments with the gyro limit (not sure if this is gain???) just says limit on the gyro and also has 2 small switches that are both on Hi. Anyhow either the tail is wagging or when i adjust the limit it drifts way too much. Any insight will be very helpful...
thanks...
Mohamad...
P.S. any other adjustments to make on dx6i like limit the travel of servo cause I think servo is moving too far...

PM  EMAIL  GALLERY  Attn:RR
01-18-2009 09:45 PM  9 years agoPost 2
neilg.

rrVeteran

north of borston

My Posts: All  Forum  Topic

isn't the gain supposed to be set at 0

In Nomeni Patri Et Fili Spiritus Sancti

PM  EMAIL  GALLERY  Attn:RR
01-18-2009 10:17 PM  9 years agoPost 3
MEL760

rrApprentice

Canton, Michigan-U.S.A.

My Posts: All  Forum  Topic

most gyros i've seen have a gain dial, this one says limit?? and I always thought gain should be set between 50-70?? Can someone elaborate please??

PM  EMAIL  GALLERY  Attn:RR
01-24-2009 01:44 AM  9 years agoPost 4
supra6

rrApprentice

Singapore

My Posts: All  Forum  Topic

Did you go through a tail set up from scratch? New gyro, servo = new tail.
As for gain, the gyro itself has a range of -100 tp +100 and the lower end is rate the higher end is Heading Hold with "0" being the cross over. Now in the TX (DX6i) you can set the gain from 0 to 100 when converted to the gyro measures this means that 50 is the crossover so anything below 50 is Rate mode and anything above 50 is HH. Also to increase the gain in HH you increase the number to increase the gain in Rate you decrease the number.

PM  EMAIL  GALLERY  Attn:RR
01-24-2009 03:02 AM  9 years agoPost 5
MEL760

rrApprentice

Canton, Michigan-U.S.A.

My Posts: All  Forum  Topic

Finally got it but I have to start all over cause I'm gonna use the GY401 instead of the G500T...I'm sure u probably have good experience with the 401 cause it's popularity, I want it in hh, that's better for newbie right? I haven't flew in a long time so slowly getting back in the game, I can hover with ease and pretty good with stall turns and basic flying with the axe cp, the blade is a little more difficult for me and I think it's because it's never been set up 100%, having said that can u recommend some magic #'s I could punch into the dx6i?
Thanks much...
Mohamad

PM  EMAIL  GALLERY  Attn:RR
WATCH
 1 page 770 views TOPIC CLOSED
HomeAircraftHelicopter
e-
Blade
Blade 400 › 3D Please help me setup my Blade 400 with new gyro and tail servo
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Thursday, June 21 - 11:37 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online