RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 2164 views POST REPLY
HomeAircraftHelicopterRadio - Spektrum DSM › ar6100e wont bind!! light never blinks it only stays solid
01-18-2009 10:55 AM  9 years agoPost 1
ryanpietro

rrNovice

vegas

My Posts: All  Forum  Topic

i put the bind plug in2 the batt slot. power on the heli and the light just stays solid. it doesnt matter if have the tx on or off. are any bind blugs different because im not sure if this plug is from my ar7000 but i figured they're all the same. what can i do to make the light blink so i can actually bind it! thanks guys

PM  EMAIL  Attn:RR  Quote
01-18-2009 11:21 AM  9 years agoPost 2
mrloudly

rrVeteran

Naseby Northampton England

My Posts: All  Forum  Topic

Un-plug all the leads. Put the bind plug (they're all the same) into the battery socket. Put the battery straight into a servo slot (making sure polarity is correct). If it doesn't enter bind mode you have a problem.

Andy M

PM  EMAIL  GALLERY  Attn:RR  Quote
01-18-2009 04:38 PM  9 years agoPost 3
chopper_crazy

rrElite Veteran

Delphos, Ohio

My Posts: All  Forum  Topic

The bind plugs should all be the same. Are you sure you have all the servos plug in the right way. I had that problem once. The light will not blink it will only stay solid. I believe the black wire of the servo will face down away from the writing on the top of the servo. Hope this helps.

It's a complex, costly, glow powered anti-gravity machine!

PM  EMAIL  GALLERY  Attn:RR  Quote
01-18-2009 09:42 PM  9 years agoPost 4
ryanpietro

rrNovice

vegas

My Posts: All  Forum  Topic

servos are on properly. i will try disconnecting now. thanks!

PM  EMAIL  Attn:RR  Quote
01-18-2009 09:44 PM  9 years agoPost 5
twitch

rrKey Veteran

Las Vegas

My Posts: All  Forum  Topic

did you push the button on the back of the transmitter before turning on. just a thought

PM  EMAIL  GALLERY  Attn:RR  Quote
01-19-2009 01:04 PM  9 years agoPost 6
leadtongue

rrNovice

S.Plainfield, New Jersey USA

My Posts: All  Forum  Topic

1. leave tx off.....2. install bind plug....3.power on heli...4.pull up and hold trainer switch do not let go of it...5. turn on the tx and wait alittle while. if it binds set down the tx unplug power from heli remove bind plug . then test to see if it took.

Installed servos on my wallet so money flys out faster!

PM  EMAIL  Attn:RR  Quote
01-19-2009 01:57 PM  9 years agoPost 7
Pinecone

rrKey Veteran

Maryalnd

My Posts: All  Forum  Topic

It the LED doesn't start flashing when powered up with the bind plug in place, it isn't going into bind mode, so NOTHING you do with Tx makes any difference.

If the LED(s) don't flash when you power up the Rx, either the bind plug is in the wrong slot (most common) or the Rx is bad.

If the Rx is bad, send back to Horizon and they will fix or replace.

If the Rx LED9s) flash on power up, but the Rx won't bind, then look to what you are doing with the Tx (bind button pushed or trainer switch held for the DX6i) BEFORE you power on, or Tx too close to the Rx. Try binding another Rx. If it works, the problem is in the first Rx. If it doesn't work with a known good Rx, the Tx is bad. Send to Horizon.

Terry
Blade CP Trex 450 SE
QJ EP8v2 EX Gaui Hurricane 550
Vibe 50 Bergen Intrepid Gasser

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 2164 views POST REPLY
HomeAircraftHelicopterRadio - Spektrum DSM › ar6100e wont bind!! light never blinks it only stays solid
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Tuesday, June 19 - 11:17 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online