RunRyder RC
 3  Topic Subscribe
WATCH
 1 page 2457 views POST REPLY
HomeAircraftHelicopterRadio - Servo - Gyro - Gov - Batt › Anyone heard of a GY611 Working with a S9254 or DS8900G Tail Servo ?
01-16-2009 12:39 AM  9 years agoPost 1
Ed Eddie Edward

rrNovice

Lockport, IL 60441 U.S.A.

My Posts: All  Forum  Topic

Can you reprogram a GY611 to work with a S9254 or a 8900G Im buying a heli from a local guy and he said someone he knows. knows how to reboot the GY611 so it works with a S9254 IS that ture and how well will it work ?

PM  EMAIL  Attn:RR  Quote
01-16-2009 12:46 AM  9 years agoPost 2
legoman67

rrElite Veteran

Nanoose Bay B.C, Canada

My Posts: All  Forum  Topic

PM  EMAIL  GALLERY  Attn:RR  Quote
01-16-2009 12:58 AM  9 years agoPost 3
Ed Eddie Edward

rrNovice

Lockport, IL 60441 U.S.A.

My Posts: All  Forum  Topic

How Well ?
Does it work if I did a 8900G would it be better or the same or less then a S9256 ? Do you know ?

PM  EMAIL  Attn:RR  Quote
01-16-2009 01:27 AM  9 years agoPost 4
legoman67

rrElite Veteran

Nanoose Bay B.C, Canada

My Posts: All  Forum  Topic

of course the slower servo will make slight differences, but unless your doing fast backwards flight or crazy 3d your not going to notice it..

PM  EMAIL  GALLERY  Attn:RR  Quote
01-16-2009 01:29 AM  9 years agoPost 5
ckd

rrApprentice

Saugus CA

My Posts: All  Forum  Topic

I use it with a 9254 on a Trex 500 and it works great. Fast backwards is no problem.

PM  EMAIL  Attn:RR  Quote
01-16-2009 01:37 AM  9 years agoPost 6
Ed Eddie Edward

rrNovice

Lockport, IL 60441 U.S.A.

My Posts: All  Forum  Topic

Well I have a choice ?
You see I could run the S9256 or I could run the 8900G and Well thats what I wounder witch would work best I know the 760P is faster on the S9256 but the 8900G is .05 so is it one in the same or will one out do the other you think?

PM  EMAIL  Attn:RR  Quote
01-16-2009 07:51 AM  9 years agoPost 7
mchammer

rrElite Veteran

California,USA

My Posts: All  Forum  Topic

Does it work if I did a 8900G would it be better or the same or less then a S9256 ? Do you know ?
I recently swapped out a 9256 for a jr 8900g on my trex 700 and it made a noticeable difference in performance.I was using a 611 gyro at the time and it improved piro consistancy over the 9256.You will have to change the framerate in the 611 gyro secret menu to make it work.After that it works nicely.If you arent doing any piro stuff you probably wont be able to notice any difference.

Peace Through Superior Firepower!!!

PM  EMAIL  GALLERY  Attn:RR  Quote
01-16-2009 01:06 PM  9 years agoPost 8
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

If you decide to go that route, make sure you reset the pulse width BEFORE you plug up the servo.

Personally I'd go with the BLS251

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
01-16-2009 04:39 PM  9 years agoPost 9
altima1779

rrKey Veteran

Toledo, oh u.s

My Posts: All  Forum  Topic

I ran the 8900g with the 611 all summer and it was awesome. At the end of the season the 8900g died while i was inverted low. There could have been many reasons the servo died.

When i sent it in to be checked out they said it died from too much heat. So i am not sure if it was due to running the 611 or just maybe a bad setup and yes i did change the pulse width from narrow to wide.

I loved the combo but i am reluctant to run it again, not knowing the true cause for the failure.

Dave

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-16-2009 05:26 PM  9 years agoPost 10
nivlek

rrProfessor

Norfolk England

My Posts: All  Forum  Topic

There could have been many reasons the servo died.
What voltage were you running it at ?

At the end of the day , it gets dark .

PM  EMAIL  Attn:RR  Quote
01-16-2009 05:27 PM  9 years agoPost 11
altima1779

rrKey Veteran

Toledo, oh u.s

My Posts: All  Forum  Topic

I was running it with an 7100r which has the built in regulator. Voltage was checked and it was i believe 5.2-5.3

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 2457 views POST REPLY
HomeAircraftHelicopterRadio - Servo - Gyro - Gov - Batt › Anyone heard of a GY611 Working with a S9254 or DS8900G Tail Servo ?
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Tuesday, June 19 - 1:50 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online