RunRyder RC
WATCH
 1 page 512 views Post Reply
Home✈️Aircraft🚁HelicopterAlignT-REX 600N › Align Governor and 9C
08-22-2008 01:48 PM  12 years ago
Topic Vote0Post 1
ckoelliker

rrElite Veteran

St. Simons, GA

MyPosts All Forum Topic
Align Governor and 9C
Can you set it up with the gov function, or do I have just use channel seven as an aux channel. I have searched, but found nothing.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 05:25 PM  12 years ago
SuperSixTwo

rrVeteran

Virginia City, NV ---USA

MyPosts All Forum Topic
I have tried the 10c and cant seem to make it work right with the gov menu. Seems the headspeed stays around 1270 no matter what i change the %'s to. I thought it might have some thing to do with the +/- of the # but dont know how to change it.

I am going change it to the atv of channel 7 instead and try again. I have another to so may change it out, but doubt it's bad.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 05:28 PM  12 years ago
ckoelliker

rrElite Veteran

St. Simons, GA

MyPosts All Forum Topic
I am going change it to the atv of channel 7 instead and try again.
If you do that, can you set multiple head speeds?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 05:32 PM  12 years ago
BarracudaHockey

rrMaster

Jacksonville FL

MyPosts All Forum Topic
Put some floats on it and bring it down. If its a 9c I can figure it out.Andy
AMA 77227
http://www.jaxrc.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 05:43 PM  12 years ago
ckoelliker

rrElite Veteran

St. Simons, GA

MyPosts All Forum Topic
I am strapping up my kite board as we speak.

Is your chimney still leaking? When the wind dies down for a moment, I swear I can hear it dripping all the way up here.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 06:16 PM  12 years ago
BarracudaHockey

rrMaster

Jacksonville FL

MyPosts All Forum Topic
hehe

I went up there yesterday and threw a tarp on it and tied it off. I just have to make sure I don't light a fire. Its kind of phallic looking, I need a stencil that says TROJAN MAGNUM
Andy
AMA 77227
http://www.jaxrc.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 08:58 PM  12 years ago
SuperSixTwo

rrVeteran

Virginia City, NV ---USA

MyPosts All Forum Topic
If you do that, can you set multiple head speeds?
I can on the 10c, as i can assign the three position switch to that channel. Since the 10 has 99% the same stuff as the 9, i would bet its the same deal.

BarracudaHockey, Ya gotta snap a pic and post it to the gallery. I have an idea what it looks like, but well, need to see it!
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 09:25 PM  12 years ago
ckoelliker

rrElite Veteran

St. Simons, GA

MyPosts All Forum Topic
Well I can assign the channel to a three position switch, but If I set my atv to the desired head speed lets say 65 will give me 2000 rpm, I can not find a way to set another value for the middle position. Lets say 1850 rpm. I cannot find a way to assign two different end points on the three position switch.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 09:27 PM  12 years ago
BarracudaHockey

rrMaster

Jacksonville FL

MyPosts All Forum Topic
Subtrim sets the middle point.

Which is all the gov menu really does.
Andy
AMA 77227
http://www.jaxrc.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 09:48 PM  12 years ago
ckoelliker

rrElite Veteran

St. Simons, GA

MyPosts All Forum Topic
If 60% gives me 1850, and 70% gives me 2000, do I set the sub trim at 60?

Or do I set it at 86 which is what % 60 is of 70.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-22-2008 11:31 PM  12 years ago
SuperSixTwo

rrVeteran

Virginia City, NV ---USA

MyPosts All Forum Topic
Forgive me here, but if you set the 3 pos switch for different atvs, and you plugged in a servo, dont you get 3 different positions on the servo? I have not tried it yet. You may be right. Iwas thinking that i may have assigned the wrong channel to the gov menu and was adjusting the wrong one.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-23-2008 01:23 AM  12 years ago
ckoelliker

rrElite Veteran

St. Simons, GA

MyPosts All Forum Topic
Well, it seems to work for me. I guess I will not know for sure until I can spool her up, but the gov. light is now turning green for the middle setting on the switch.

Once again Andy "lights the lamp".
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 512 views Post Reply
Home✈️Aircraft🚁HelicopterAlignT-REX 600N › Align Governor and 9C
Print TOPIC

 1  Topic Subscribe

Saturday, September 26 - 6:58 am - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online