RunRyder RC
 3  Topic Subscribe
WATCH
 1 page 481 views POST REPLY
HomeAircraftHelicopterMain Discussion › Trying to get flying after heli crash
03-10-2008 01:07 AM  10 years agoPost 1
jduncc

rrNovice

Charlotte, NC

My Posts: All  Forum  Topic

Hello. I have been in rc for quite a while. A few years ago I decided to get into flying heli's and i bought a raptor 30. I was able to hover pretty well, and without the training gear. However, I had a pretty good crash. I rebuilt the heli and then haven't flown it in a few years. I'm trying to get back into it again and I need some help. I went ahead and fired it up, and when I throttle up, the heli starts shaking pretty bad. I'm afraid to give it more up b/c I think it might crash. I did some reading in some of these forums, and it sounds like my main rotors are out of alignment. One website suggested putting red tape on one rotor and yellow on the other. then spin it up and look a the blades to see if you can see both colors of tape. I can see both colors, and I trid adjusting the link that controls the rotors, but it doesn't seem to help. what other advice can you give me?

I'm also looking to see if there are any other heli pilots in the Charlotte area. I'd really appreciate some help.

Thanks!

Raptor 30 (V1)
Futaba 8UAP
OS 32 Engine

PM  EMAIL  Attn:RR  Quote
03-10-2008 01:36 AM  10 years agoPost 2
Yug

rrMaster

UK. Herts

My Posts: All  Forum  Topic

Balance everything properly and if you're lacking confidence, get an experienced pilot to lift off and track your blades.
Buy a sim.

Vegetable rights and Peace

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2008 01:57 AM  10 years agoPost 3
AWW618

rrApprentice

Highlands Ranch CO

My Posts: All  Forum  Topic

Did you change all your shafts sounds like one might be bent.

don't fear a crash it happens. It's a great hobby stick with it.

pick it up and shake it off...she'll fly again

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2008 02:12 AM  10 years agoPost 4
Jujiro

rrApprentice

Jennings, Louisiana- USA

My Posts: All  Forum  Topic

Yea I try my best not to let crashing scare me to much, I just look at it as something to learn from not as loosing the heli since I can just repair it . Whenever I crash I try to recall exactly what happened and what caused it. Like the other week I crashed my t-rex 450 while doing circuits because I forgot to add more throttle when I turned into the wind and didn't pull up fast enough.

Anyways like AWW618 said it could be a bent shaft, but also check to make sure the bolts on your main blades aren't to tight so the blades can straighten themselves out during spool up.

PM  EMAIL  Attn:RR  Quote
03-10-2008 02:15 AM  10 years agoPost 5
David Blain

rrKey Veteran

Mt. Dora, Florida (USA)

My Posts: All  Forum  Topic

jduncc--
Start at the basics, Look at the "everything" in the rotor head... Make sure the main shaft is true,if not start replacing! check your bearings,look at the feathering shaft, flybar etc... Then adress the blades, IF they are wood get rid of them, They are warped with age.... Get new ones, balance them and IF I know Raptors, It will spin true after you track it in....
Good luck and let us know how it all works out!

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 481 views POST REPLY
HomeAircraftHelicopterMain Discussion › Trying to get flying after heli crash
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Sunday, June 24 - 10:16 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online