RunRyder RC
 0  Topic Subscribe
WATCH
 1 page 619 views POST REPLY
HomeAircraftHelicopterAlignOther › Helicommand on an Align 600n?
03-09-2008 11:06 PM  10 years agoPost 1
dbthunder15

rrNovice

arvada, CO

My Posts: All  Forum  Topic

Has anyone installed the helicommand 3d on an align 600 nitro yet? If so can you please help me out! im lost like a fat kid in a candy store i just dont know where to start! lol thanks
Nic

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2008 11:22 PM  10 years agoPost 2
JIMHELI

rrNovice

ireland

My Posts: All  Forum  Topic

hi have you got pc software as well

PM  EMAIL  Attn:RR  Quote
03-09-2008 11:38 PM  10 years agoPost 3
dbthunder15

rrNovice

arvada, CO

My Posts: All  Forum  Topic

no i didnt get that yet i didnt relize i needed it for easier set up but will be getting it soon... are there installation pics on there?

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2008 11:48 PM  10 years agoPost 4
JIMHELI

rrNovice

ireland

My Posts: All  Forum  Topic

no pic realy on my one the book was in german .so i down loaded english one. i have only had it 2 days , the software makes it a lot easer to set up,whats the problem you have

PM  EMAIL  Attn:RR  Quote
03-09-2008 11:55 PM  10 years agoPost 5
dbthunder15

rrNovice

arvada, CO

My Posts: All  Forum  Topic

well i dont know if maybe i can get an extension cable for the grey box but i cant get it to reach my reciever... i think i might have found a place to relocate everything but not sure if that is the correct way to do it. and the four single wires with connectors on them, where do they all go? and another question is i would like to use my gy401 gyro is there a way to bypass the helicommands gyro? or do you just not hook that up?

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2008 12:25 AM  10 years agoPost 6
JIMHELI

rrNovice

ireland

My Posts: All  Forum  Topic

right the four wires go to your rx from the clear robby bord, the twisted on plugs in to the top of HC the longer slot blake to outside yellow near the butten,the first red/wit/blk gust under the small vn on label side goes to aile,next red/wit/blk elev,leave 401 plug were thay are,orange goes to aux one or pitch i think green to aux 2 now im useing pcm 9 x wich you would call 9303 jr.you can mount the HC TO THE FRONT ROUND SIDE OUT/REAR/LEFT/RIGHT BUT TRY TO PUT IT SOMEWERE IT WONT GET COVERD IN OIL FROM FUIL YOU CAN ALLSO PUT IT INSIDE BUT IN THAT WAY WILL WORK IN HORIZON MODE im still useing my 401 as well

PM  EMAIL  Attn:RR  Quote
03-10-2008 12:42 AM  10 years agoPost 7
dbthunder15

rrNovice

arvada, CO

My Posts: All  Forum  Topic

do you also have a align 600n?

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2008 12:55 AM  10 years agoPost 8
MJHiscott92504

rrVeteran

James Hiscott , Germany for past 11 months

My Posts: All  Forum  Topic

?
Do you have a photo of a Klondyke bar?

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2008 12:59 AM  10 years agoPost 9
JIMHELI

rrNovice

ireland

My Posts: All  Forum  Topic

no i have a titon its a one twenty swash e-ccpm but the rx setup is the same but aux 1 & 2 may differ depends on your tx http://www.helicommand.com/ have a look hear you may get a manual & when you get software down load update i think you can also get a manule at that link also you need a blank chanell on tx set to one servo swash type all trims centerd as helcommand does the rest for you but TBO its way easer with pc

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 619 views POST REPLY
HomeAircraftHelicopterAlignOther › Helicommand on an Align 600n?
 Print TOPIC  Make Suggestion 

 0  Topic Subscribe

Wednesday, June 20 - 11:59 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online