RunRyder RC
WATCH
 1 page 921 views POST REPLY
HomeRC & PowerAircraftHelicopterRadio - JR DMSS › dx6i and jr9303
02-11-2008 01:43 AM  10 years agoPost 1
az_heliguy

rrKey Veteran

San Tan Valley, AZ

My Posts: All  Forum  Topic

okay...

so the 9303 and dx6i are both made by jr supposedly...

i have a buddy who i am trying to teach fly and he has a dx6i and i have my 9303. the dx6i has to be the master and im using my 9303 as the slave. when i setup all the same trims, rev, etc on the 9303 that the dx6i has, everything is good except the rudder and throttle, collective and cyclic are okay and correct.

does anyone have any info on this by chance? can the 9303 be a slave to the dx6i. we would use them the other way around, but since it has the spektrum rx, his has to be the master right???

PM  EMAIL  GALLERY  Attn:RR  Quote
02-11-2008 03:49 PM  10 years agoPost 2
Pinecone

rrKey Veteran

Maryalnd

My Posts: All  Forum  Topic

Why do you want the 9303 as the slave?

If he is learning to fly and owns the DX6i, you want him to use HIS radio to get used to the feel. And the student flies the slave.

You have to set up the 9303 to fly the model, not just copy the settings.

Terry
Blade CP Trex 450 SE
QJ EP8v2 EX Gaui Hurricane 550
Vibe 50 Bergen Intrepid Gasser

PM  EMAIL  Attn:RR  Quote
02-11-2008 04:00 PM  10 years agoPost 3
9387ASH

rrElite Veteran

UK

My Posts: All  Forum  Topic

del'd

PM  EMAIL  Attn:RR  Quote
02-11-2008 04:06 PM  10 years agoPost 4
az_heliguy

rrKey Veteran

San Tan Valley, AZ

My Posts: All  Forum  Topic

its not that i want the 9303 as the slave, but it has to be the slave. since the heli has the spektrum rx installed, the 9303 cannot be the master, the dx6i needs to be. im still waiting for a response from spektrum directly on this issue as well...

PM  EMAIL  GALLERY  Attn:RR  Quote
02-11-2008 04:07 PM  10 years agoPost 5
az_heliguy

rrKey Veteran

San Tan Valley, AZ

My Posts: All  Forum  Topic

i will be on the dx6i and have him on the 9303, lol...

PM  EMAIL  GALLERY  Attn:RR  Quote
02-11-2008 04:14 PM  10 years agoPost 6
9387ASH

rrElite Veteran

UK

My Posts: All  Forum  Topic

Thats the only way but...... inherent danger is that if he panics, you are totally reliant on him pressing the button/switch to transfer the primary channels over to you.

I hate to say it, but its a recipe for a prang !

PM  EMAIL  Attn:RR  Quote
02-12-2008 02:37 AM  10 years agoPost 7
Pinecone

rrKey Veteran

Maryalnd

My Posts: All  Forum  Topic

Sorry, I was thinking X9303, not XP9303.

So just buy an X9303.

Terry
Blade CP Trex 450 SE
QJ EP8v2 EX Gaui Hurricane 550
Vibe 50 Bergen Intrepid Gasser

PM  EMAIL  Attn:RR  Quote
02-12-2008 02:55 PM  10 years agoPost 8
Adams

rrApprentice

Champaign Il. USA

My Posts: All  Forum  Topic

The DX6i can be used as a master or slave with any Spektrum or JR radio including the 9303. Each radio must be set up with the correct parameters (servo reverse, travel adjustments, pitch curves, etc.)to fly the model but when properly set up, either radio can be used as a master or slave. Of coarse the master must be bound to the model.

PM  EMAIL  Attn:RR  Quote
02-12-2008 08:01 PM  10 years agoPost 9
Pinecone

rrKey Veteran

Maryalnd

My Posts: All  Forum  Topic

You made the same mistake as I did, he has an XP9303, NOT an X9303.

But the other good thing about using a 9303 as Master is you can have it run in a mode where the slave DOESN'T have to be fully set up the same, as the Master takes the stick input only from the Slave and processes the data itself.

This also allows you to only give certain channels to the student.

Terry
Blade CP Trex 450 SE
QJ EP8v2 EX Gaui Hurricane 550
Vibe 50 Bergen Intrepid Gasser

PM  EMAIL  Attn:RR  Quote
02-12-2008 08:43 PM  10 years agoPost 10
az_heliguy

rrKey Veteran

San Tan Valley, AZ

My Posts: All  Forum  Topic

yes, this is the xp9303, no 2.4 module in it, if there was, this thread wouldnt have even been started and we would already be in the air, lol... but it still should work with the dx6i as the master and the xp9303 as the slave with no hitch. im all aware of making sure both radios are setup the same and everything, this isn't my first rodeo so to speak, lol... but as stated before, everything is correct except rudder and throttle, they are backwards no matter how they are setup in the slave (xp9303)...

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 921 views POST REPLY
HomeRC & PowerAircraftHelicopterRadio - JR DMSS › dx6i and jr9303
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Thursday, December 13 - 6:34 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online