RunRyder RC
WATCH
 2 pages [ <<    <    ( 1 )     2     NEXT    >> ] 850 views TOPIC CLOSED
HomeClassifiedAircraftHelicopterClassifieds - Engines & Mufflers Sold  YS50 for sale $200 shipped
02-11-2008 01:23 AM  10 years agoPost 1
Brovic777rrElite Veteran - Los Angeles, CA - My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

I have a YS50st that has been run 7 tanks. It has been rebuilt by YS Parts and Services and is as good new. Already bought another engine so I don't need this anymore.

Selling for $200 shipped.

USA ONLY
PAYPAL ONLY

Killer Beam E4 450
Check out my HD Gallery

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
02-11-2008 01:39 AM  10 years agoPost 2
ErichF

rrElite Veteran

Sutton, NH

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Why was it rebuilt after 7 tanks?

PM  EMAIL  GALLERY  Attn:RR
02-11-2008 01:40 AM  10 years agoPost 3
Thomas_W

rrApprentice

Shenandoah,Va USA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

and why is the piston discolored and have scratches on it if it was rebuilt by YS parts and services?

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
02-11-2008 01:46 AM  10 years agoPost 4
WayneBrown

rrNovice

Augusta, GA

My Posts: All  Forum  Topic

My Classified Activity
No Classified Feedback
Add Classified Feedback

whats up wid dat?
Why the caramel color on the piston too? if it's rebuilt, what'd they rebuild, the carb spacer?

PM  EMAIL  Attn:RR
02-11-2008 01:47 AM  10 years agoPost 5
fiveoboy01

rrVeteran

Waunakee, WI - USA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

That last pic, just below the carb flange on the crankcase, is that a crack or casting flaw? Did you hit it with something?

Could you post another pic from a different angle?

Mikado Logo 400, hopefully ready by spring.

PM  EMAIL  Attn:RR
02-11-2008 01:48 AM  10 years agoPost 6
Racer38

rrApprentice

The Great White North ( MA )

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Hmmm ya mean the spacer right next to the spot that looks like a crack in the case ??????

Craig (Alias Racer38)

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
02-11-2008 01:48 AM  10 years agoPost 7
Brovic777

rrElite Veteran

Los Angeles, CA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

It was rebuilt after 5 tanks due to the crankshaft bolt breaking off in my fan hub. I then ran it another two tanks after that, but decided to keep the OS Hyper 50 I had before becase I need the money of this sale.

Don't know about the scratches? It was only flown 2 tanks after being rebuilt.

Killer Beam E4 450
Check out my HD Gallery

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
02-11-2008 01:49 AM  10 years agoPost 8
CincyQuake

rrApprentice

Cincinnati, Ohio

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

And WHY and WHY and WHY

Until next time.... Keep them rotors outta the dirt....

PM  EMAIL  HOMEPAGE  Attn:RR
02-11-2008 01:50 AM  10 years agoPost 9
Thomas_W

rrApprentice

Shenandoah,Va USA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

whats up w/ the shiny spot on the case at the front bearing mounting surface? what was rubbing on it to cause that? Has it been in any crashes? If so, how many?

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
02-11-2008 01:51 AM  10 years agoPost 10
WayneBrown

rrNovice

Augusta, GA

My Posts: All  Forum  Topic

My Classified Activity
No Classified Feedback
Add Classified Feedback

how'd u break the crankshaft? hammer?

PM  EMAIL  Attn:RR
02-11-2008 01:51 AM  10 years agoPost 11
fiveoboy01

rrVeteran

Waunakee, WI - USA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

What constitutes a rebuild? Please clarify.

Mikado Logo 400, hopefully ready by spring.

PM  EMAIL  Attn:RR
02-11-2008 01:53 AM  10 years agoPost 12
Thomas_W

rrApprentice

Shenandoah,Va USA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

What "crankshaft" bolt broke off in your fan hub? you mean the crankshaft itself broke? or the nut broke? please clarify, i'm interested, but need more info.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
02-11-2008 02:01 AM  10 years agoPost 13
Brovic777

rrElite Veteran

Los Angeles, CA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

The shiny spot is from the rubber mounts for the Knight 50 3D. It was a tight fit and I had to slid it in.

The crankshaft broke off in flight on the bolt. The heli just came down for a hard landing. Skids didn't even break.

The rebuilt was full rebuid. They changed out everything. Wrist Pin, Liner, Piston Set and Crankshaft. Don't know why there would be scatches on the piston after after only two tanks.

Killer Beam E4 450
Check out my HD Gallery

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
02-11-2008 02:02 AM  10 years agoPost 14
fiveoboy01

rrVeteran

Waunakee, WI - USA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

So you're saying that piston has TWO tanks of fuel through it?

What about that ding on the crankcase to the rear of the carb flange?

Mikado Logo 400, hopefully ready by spring.

PM  EMAIL  Attn:RR
02-11-2008 02:02 AM  10 years agoPost 15
CincyQuake

rrApprentice

Cincinnati, Ohio

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

What heli would you like to see it go in?

Until next time.... Keep them rotors outta the dirt....

PM  EMAIL  HOMEPAGE  Attn:RR
02-11-2008 02:02 AM  10 years agoPost 16
Thomas_W

rrApprentice

Shenandoah,Va USA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

What BOLT? the crankshaft is threaded, so where does the "bolt" go? b/c the crankshaft isn't drilled and tapped down the center

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
02-11-2008 02:03 AM  10 years agoPost 17
WayneBrown

rrNovice

Augusta, GA

My Posts: All  Forum  Topic

My Classified Activity
No Classified Feedback
Add Classified Feedback

I thought the Knight has a silicone mount, yours is rubber?
How'd that hold up to the exhaust residue?

PM  EMAIL  Attn:RR
02-11-2008 02:04 AM  10 years agoPost 18
CincyQuake

rrApprentice

Cincinnati, Ohio

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Would this fit into a G scale train?

Until next time.... Keep them rotors outta the dirt....

PM  EMAIL  HOMEPAGE  Attn:RR
02-11-2008 02:05 AM  10 years agoPost 19
Racer38

rrApprentice

The Great White North ( MA )

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Hey if it fits a plane what size prop will it turn ?? Is that a clockwise or counter clockwise engine ??

Craig (Alias Racer38)

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
02-11-2008 02:05 AM  10 years agoPost 20
WayneBrown

rrNovice

Augusta, GA

My Posts: All  Forum  Topic

My Classified Activity
No Classified Feedback
Add Classified Feedback

would you take $100? it looks used to me.

PM  EMAIL  Attn:RR
WATCH
 2 pages [ <<    <    ( 1 )     2     NEXT    >> ] 850 views TOPIC CLOSED
HomeClassifiedAircraftHelicopterClassifieds - Engines & Mufflers Sold  YS50 for sale $200 shipped
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Classifieds › HELP-FAQ
Attention Buyers! To receive feedback Post Reply in the seller’s topic. The seller can then click your post's Add Classified Feedback link.
Attention Sellers! Stating price is not mandatory but recommended. Post Reply commentary that interferes with the selling process (and not replied to) will be removed upon request. Click Attn:RR on the offending classified post. Repeated NIB-NIP sales are not allowed. Take it to EBay.
Buyer Beware! RunRyder cannot vouch for any seller's or buyer's credibility and will not accept responsibility for any transactions resulting from the use of this site.

Thursday, December 13 - 2:31 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online