RunRyder RC
WATCH
 1 page 753 views Post Reply
Home✈️Aircraft🚁HelicopterHelicopter Main Discussion › Does the New YS 50 engine fit the T-Rex 600 Nitro Pro
08-04-2007 01:06 AM  13 years ago
Topic Vote0Post 1
Joseph Lu

rrNovice

Campbelll, CA

MyPosts All Forum Topic
Does the New YS 50 engine fit the T-Rex 600 Nitro Pro
Hi,

Does any one konw if the New YS 50 engine fits the T-Rex 600 Niro Pro without any modification?

Thanks,

--Joseph
SHARE  PM  EMAIL  Attn:RR  Quote
08-04-2007 01:08 AM  13 years ago
RPM 1.5 (RIP)

rrKey Veteran

Cape May New Jersey

MyPosts All Forum Topic
NO PROBLEM
Mines been running great after I got back from YS service,using the new JK pipe{one peice}
Ray
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-04-2007 01:16 AM  13 years ago
hootowl

rrProfessor

Garnet Valley, Pa.

MyPosts All Forum Topic
Only problem I had was the main hub nut was too tall. You either need to cut it down a little or use an OS one.

The clutch shoe will hit it in the center during install if you don't be careful.
Wolves don't lose sleep over the opinions of sheep
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
08-04-2007 01:33 AM  13 years ago
Joseph Lu

rrNovice

Campbelll, CA

MyPosts All Forum Topic
Thanks guys. Will the T-Rex 600 engine mount work with YS50?

I haven't tried the YS50 yet. Does it over-perform OS50 Hyper?

Thanks,

--Joseph
SHARE  PM  EMAIL  Attn:RR  Quote
08-04-2007 01:50 AM  13 years ago
jackheli

rrProfessor

Vancouver - Canada

MyPosts All Forum Topic
Also, it there a problem with pressure on the tank, making it expand and hit something?

Not sure if th YS50 has the same pressurized system as its bigger brothers...
It's easy to find an excuse to do wrong. Hard is not to find an excuse to do right.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-04-2007 01:52 AM  13 years ago
hootowl

rrProfessor

Garnet Valley, Pa.

MyPosts All Forum Topic
Mounts fit perfectly, no expansion issue.Wolves don't lose sleep over the opinions of sheep
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
08-04-2007 03:52 AM  13 years ago
bsc

rrNovice

Villa Park, IL

MyPosts All Forum Topic
Only problem I had was the main hub nut was too tall. You either need to cut it down a little or use an OS one.
I read that from someone else as well, but I didn't have that issue. Could you actually tell that it was hitting the clutch? I was able to fully seat my clutch without any issue using the ys nut. Or was it the start shaft that was hitting? I didn't notice my start shaft having any issues, but I didn't pull it apart to check for any rubbing either.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-04-2007 08:58 AM  13 years ago
hootowl

rrProfessor

Garnet Valley, Pa.

MyPosts All Forum Topic
No it wasn't the start shaft. The one way bearing that's inside the clutch hits the nut before the clutch fully seats on the hub.Wolves don't lose sleep over the opinions of sheep
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
08-04-2007 01:07 PM  13 years ago
bsc

rrNovice

Villa Park, IL

MyPosts All Forum Topic
That could explain it then. Your bearing must have been pressed in a little further than mine at the factory.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 753 views Post Reply
Home✈️Aircraft🚁HelicopterHelicopter Main Discussion › Does the New YS 50 engine fit the T-Rex 600 Nitro Pro
Print TOPIC

 3  Topic Subscribe

Wednesday, September 30 - 12:54 am - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online