RunRyder RC
WATCH
 1 page 729 views Post Reply
Home✈️Aircraft🚁HelicopterAlignOther › One Way Press Fit
08-02-2007 01:00 PM  13 years ago
Topic Vote0Post 1
ringram2077

rrApprentice

Birmingham, AL

MyPosts All Forum Topic
One Way Press Fit
When pressing in a new one way is any kind of retainer (loktite, etc.)required ?
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
08-02-2007 01:58 PM  13 years ago
JMF

rrApprentice

Clinton

MyPosts All Forum Topic
One gentleman was saying to use a touch of loctite because his bearing spun inside the hub without it.
Hope I helped.
Look at the "one way issue count" I seen it in there somewheres.
SHARE  PM  EMAIL  Attn:RR  Quote
08-02-2007 08:42 PM  13 years ago
ringram2077

rrApprentice

Birmingham, AL

MyPosts All Forum Topic
Yep, it will need some retainer. You can push the new one way back in by hand. I am using some of the green that came with the kit. Hope it holds. I also cleaned out the new one way and plan to try the white lithium grease. Will see how it works tomorrow.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
08-02-2007 09:13 PM  13 years ago
helibird

rrKey Veteran

St. George, UT

MyPosts All Forum Topic
Yes locktite it in. I had mine spin in the hub, sucked cause I thought it was the clutch slipping and I dropped the engine to check.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-02-2007 09:31 PM  13 years ago
j5coat

rrVeteran

Phoenix

MyPosts All Forum Topic
mine did not press in by hand, it was in fact very tight. I did not use any loctite on it and it has been fine. But just to be safe use a dab of green once you get it in place, that should hold it great.Trex 700, Trex 600n
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-06-2007 02:43 PM  13 years ago
helibird

rrKey Veteran

St. George, UT

MyPosts All Forum Topic
Mine didn't press in by hand either but it spun after a couple flights.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-06-2007 03:42 PM  13 years ago
LJS

rrKey Veteran

Minnesota, USA

MyPosts All Forum Topic
I just replaced my autorotation bearing. It pressed in so easily that I'm concerned it might not hold even with loctite. I've got four flights on it and so far, so good.

Keep 'em flying.

LJS
Logo 600 VBar, 10S
TRex 600E VBar, 8S
Logo 500 VBar, 6S
TRex 600ESP, 6S
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-07-2007 12:50 AM  13 years ago
ringram2077

rrApprentice

Birmingham, AL

MyPosts All Forum Topic
After some green loktite I shot some thin CA in for insurance. It is holding fine even though the new one way is still locking.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
08-07-2007 11:41 AM  13 years ago
JMF

rrApprentice

Clinton

MyPosts All Forum Topic
what brand of new one way are you using?
SHARE  PM  EMAIL  Attn:RR  Quote
08-07-2007 12:04 PM  13 years ago
ringram2077

rrApprentice

Birmingham, AL

MyPosts All Forum Topic
So far I am using the same type that came with the kit. Align is suppose to have a new one available soon (HN6064). The one I just replaced also locks up, just not as tight. I used the white lithium. I may try once more with triflo or atf and see if that is any better.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 729 views Post Reply
Home✈️Aircraft🚁HelicopterAlignOther › One Way Press Fit
Print TOPIC

 4  Topic Subscribe

Friday, September 25 - 4:47 am - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online