RunRyder RC
WATCH
 1 page 544 views Post Reply
Home✈️Aircraft🚁HelicopterBeginners Corner › Servo Throws... again =\
08-02-2007 02:21 AM  13 years ago
Topic Vote0Post 1
darkfa8

rrElite Veteran

Brick, NJ - USA

MyPosts All Forum Topic
Servo Throws... again =\
I'm setting up a Trex with a microheli frame, again...

anyway, in the radio: 50% at all points in Normal mode, servo arms were set by eye to be perpendicular the mainshaft, all links from the servos to swash are the same length, at 50% collective I get 0* pitch on the mains and all mixers, flybar, main grips are level.

when i switch to my idle-up (0-100% pitch curve) and I go to low stick I get about -6*, at full stick I get 11* and the washout base is butted up against the bottom of the head yoke.

How do I get this equalled out and have 0* at mid-stick/50%?
- Dan Goldstein
Team Revolectrix
Lynx Heli Innovations
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-02-2007 12:38 PM  13 years ago
Morris

rrApprentice

Hong Kong

MyPosts All Forum Topic
What Tx do you use?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-02-2007 12:56 PM  13 years ago
BarracudaHockey

rrMaster

Jacksonville FL

MyPosts All Forum Topic
Many radios allow pitch trimming in normal mode as well as high / low pitch points adjustable by knobs or sliders.

Make sure they are centered or disabled or do your setup in idle up.
Andy
AMA 77227
http://www.jaxrc.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-02-2007 02:55 PM  13 years ago
darkfa8

rrElite Veteran

Brick, NJ - USA

MyPosts All Forum Topic
futaba 9c- Dan Goldstein
Team Revolectrix
Lynx Heli Innovations
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-02-2007 03:11 PM  13 years ago
BarracudaHockey

rrMaster

Jacksonville FL

MyPosts All Forum Topic
Yep, HOV-PIT and HOV-THR should be inhibited.

High/Low pitch should be set to MANUAL and NULL for normal and idle 1.
Andy
AMA 77227
http://www.jaxrc.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-02-2007 03:28 PM  13 years ago
darkfa8

rrElite Veteran

Brick, NJ - USA

MyPosts All Forum Topic
my hov-pit & hov-thr were set mix>inh, but for vr i had a switch assigned so I changed that to "null" for both.

i don't understand:

"High/Low pitch should be set to MANUAL and NULL for normal and idle 1."

Where is this set in the radio menu?

My current Swash AFR:
ail>-40%
ele>+40%
pit>-25%
- Dan Goldstein
Team Revolectrix
Lynx Heli Innovations
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-05-2007 10:14 AM  13 years ago
mikeflyz

rrApprentice

Westlake Village, CA

MyPosts All Forum Topic
"High/Low pitch should be set to MANUAL and NULL for normal and idle 1."

Where is this set in the radio menu?
This is for the 9C Super. It's on the ADVANCED MENU, and the procedure is on pg. 94 in the manual. This function doesn't exist on the earlier 9C's.

I'm assuming all your endpoints are at 100% for 1, 2 and 6.

Best of luck.
Mike
MA Fury Extreme, JetCopter SX
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-05-2007 01:11 PM  13 years ago
BarracudaHockey

rrMaster

Jacksonville FL

MyPosts All Forum Topic
Thats true, if you dont have the 9CSuper it doesn't apply to you.

However if you have the original 9c then REVO is enabled by defualt and you want to turn that off if you have a heading hold gyro.
Andy
AMA 77227
http://www.jaxrc.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 544 views Post Reply
Home✈️Aircraft🚁HelicopterBeginners Corner › Servo Throws... again =\
Print TOPIC

 5  Topic Subscribe

Wednesday, September 30 - 6:30 am - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online