WATCH |
1 page 927 views |
Post Reply |
05-27-2007 11:56 PM 13 years ago
| a_araujo
rrNovice Portugal |
N9 with Hitec servos Does anyone use hitec servos on the N9 ?Araujo |
| SHARE PM EMAIL Attn:RR Quote |
05-28-2007 12:10 AM 13 years ago
| Awamori
rrApprentice Minot, ND |
Not me but I would imagine the HS6965's would work just fine. Only for something using CCPM, but not on something like a raptor 90. |
| SHARE PM EMAIL GALLERY Attn:RR Quote |
05-28-2007 12:15 PM 13 years ago
| Saleh
rrVeteran Kuwait |
i dont think that they would fit as i have tried b4 but size diffrantIf you aint crashing you aint flyin |
| SHARE PM EMAIL HOMEPAGE GALLERY Attn:RR Quote |
05-28-2007 07:05 PM 13 years ago
| DOKEY
rrProfessor Northamptonshire UK |
The Hitec 6965's are great for the price considering there speed and power!! but what lets them down, is there resolution. There is a noticeable difference between the Hitec's and say Futaba or JR when used on the cyclic's.  Ryan. |
| SHARE PM EMAIL HOMEPAGE GALLERY Attn:RR Quote |
05-28-2007 08:42 PM 13 years ago
| Awamori
rrApprentice Minot, ND |
The Hitec 6965's are great for the price considering there speed and power!! but what lets them down, is there resolution. There is a noticeable difference between the Hitec's and say Futaba or JR when used on the cyclic's. |
| SHARE PM EMAIL GALLERY Attn:RR Quote |
05-29-2007 03:33 AM 13 years ago
 BPFlyer
rrApprentice Wichita, KS |
Double check those Airtronics 94758Z servos! Try using your finger to hold the swash plate from moving. You will see that you can keep the swash from traveling pretty easily. The rated force on these servos does not translate accurately to swash power!Now try the same thing with say a Futaba S9351, the result is much different. You might end up with a blood blister, the difference is crazy.I started with the Airtronics, found some issues and then swapped to the Futaba S9351 servos. Been very happy since. Specs don't tell the whole story.Fly it like you stole it! |
| SHARE PM EMAIL GALLERY Attn:RR Quote |
05-29-2007 05:54 PM 13 years ago
| Awamori
rrApprentice Minot, ND |
I agree some what, but it's obvious in, it's all who you ask!Nigel Brown quote:
Hi Guys,
I've just converted over to the JR DS8711 servos on cyclic/collective in the N9. They are more precise around centre stick and make the model feel even more looked in than with 9351's. You will not be dissapointed Cheers Nigel wolfcbr2003:Servo's Here is a servo to look at. How about the Hitec 6975hb. 144oz torque and 6.0 volts and .10 speed I have over a 100 flight on my trex 600 and no slop at all. I have 5 gallons on the Synergy with 9351's and have metal slop. I think I am going totrythe 6975's onthis bird next. Marcus
Sorry for the hi-jack.... |
| SHARE PM EMAIL GALLERY Attn:RR Quote |
05-29-2007 08:03 PM 13 years ago
| Saleh
rrVeteran Kuwait |
I'm telling you again Hitec wont fit in the N9 as i have tried installing 5925 but thier size is diffrant as they are smaller than futaba and jrIf you aint crashing you aint flyin |
| SHARE PM EMAIL HOMEPAGE GALLERY Attn:RR Quote |
05-29-2007 08:33 PM 13 years ago
| Awamori
rrApprentice Minot, ND |
yeap I measured and they have a little bit closer hole spacing. It's close but the way the N9 is pre-drilled I don't see how you could use the Hitec's |
| SHARE PM EMAIL GALLERY Attn:RR Quote |
05-30-2007 04:43 AM 13 years ago
| Dusty
rrApprentice Edmonton, Alberta - Canada |
All the hitec servo's I've tried in the Synergy didn't work very well.They don't seem to center well enough to get a good setup.However... in a non CCPM setup, they work just fine.
I've got them in my R90.Try the Futaba 9351's.So far they're working great!Canada Shawn |
| SHARE PM EMAIL HOMEPAGE Attn:RR Quote |
05-31-2007 05:43 PM 13 years ago
| Saleh
rrVeteran Kuwait |
i run 9351 on mine and i have seen 9451 in action they seem to be better, as they are faster and the tourqe is less but you wont need tha tourqe of the 9251 its to muchIf you aint crashing you aint flyin |
| SHARE PM EMAIL HOMEPAGE GALLERY Attn:RR Quote |
WATCH |
1 page 927 views |
Post Reply |
3 Topic Subscribe
Monday, January 18 - 2:03 pm - Copyright © 2000-2021 RunRyder EMAIL • Enable Cookies
0
