Tail Servo Buzzing

rrTV-PHOTO GALLERIES MY GALLERY HELP-FAQ

myHOME PM pmRR MEMBERS 268 ONLINE 1 EVENTS SEARCH REGISTER START HERE

WATCH

1 page 565 views

Post Reply

RunRyder	RunRyder

Home › ✈️Aircraft › 🚁Helicopter › Beginners Corner › Tail Servo Buzzing

05-21-2007 03:17 PM 13 years ago

Topic Vote

0Post 1

scrplyr5

rrNovice

Montgomery, AL

MyPosts All Forum Topic

Tail Servo Buzzing

I am running a raptor 30 V1 with a GY401 and Futaba 9254 Servo. I have noticed that the servo buzzes excessivly with no imputs added. I was wondering if there was any way to get rid of this buzz and increase the life of my RX Battery. Any Help would Be great!! Thanks In Advance

Jim

SHARE PM EMAIL GALLERY Attn:RR Quote

05-21-2007 03:50 PM 13 years ago

0Post 2

BarracudaHockey

rrMaster

Jacksonville FL

MyPosts All Forum Topic

Digital servos buzz, its normal. They whine pretty good of there's a load on the servo but they chatter just sitting there, wait till you have a few 9252s on collective and cyclic!Andy
AMA 77227
http://www.jaxrc.com

SHARE PM EMAIL GALLERY Attn:RR Quote

05-21-2007 04:54 PM 13 years ago

0Post 3

airboss

rrElite Veteran

OC ,california

MyPosts All Forum Topic

buzzzzz

its ok for the heli to be buzzing,but not the operator.Urukay HPS3 KSE 700 HPS3

SHARE PM EMAIL GALLERY Attn:RR Quote

05-21-2007 07:27 PM 13 years ago

0Post 4

pgrbff

rrVeteran

Piemonte, Italy

MyPosts All Forum Topic

I just set up my airskipper with 9252s on ccpm, boy do they whine! Is it OK? Are they being worn out?Proficient at turning cash and credit into smoke and noise!

SHARE PM EMAIL GALLERY Attn:RR Quote

05-22-2007 01:13 AM 13 years ago

0Post 5

airboss

rrElite Veteran

OC ,california

MyPosts All Forum Topic

push pull

if your linkage rods are not properly adjusted you will get buzzz.but most digital servos humm a little,no worries.Urukay HPS3 KSE 700 HPS3

SHARE PM EMAIL GALLERY Attn:RR Quote

05-22-2007 04:23 AM 13 years ago

0Post 6

baddynergy

rrElite Veteran

sierra madre, ca- usa

MyPosts All Forum Topic

On the raptor the tail shouldnt make any noise except occasional buzzing, NOT constant. IF it is buzzing constantly your tail linkage guides are the most likely culprit. Try tweaking each one until it stops then Ca it solid.

Could also be tight ball links.

With properly setup linkage the digital servos should not make any noise at rest, save an occasional buzz or beep.**Unattended children will be givin a shot of espresso and a puppy**

SHARE PM EMAIL GALLERY Attn:RR Quote

05-22-2007 08:55 AM 13 years ago

0Post 7

pgrbff

rrVeteran

Piemonte, Italy

MyPosts All Forum Topic

With only a couple of mm of threaded rod showing between the plastic push rod ends on a push-pull set-up, and the JR pushrod ends needing 2 full turns per adjustment,(they're sided), how do you fine adjust the setup?Proficient at turning cash and credit into smoke and noise!

SHARE PM EMAIL GALLERY Attn:RR Quote

WATCH

1 page 565 views

Post Reply

RunRyder	RunRyder

Home › ✈️Aircraft › 🚁Helicopter › Beginners Corner › Tail Servo Buzzing

Print TOPIC

2 Topic Subscribe

New Subscriptions

Buddies Online