RunRyder RC
WATCH
 1 page 620 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Servo - Gyro - Gov - Batt › Notchy 9254 - but no gears stripped?
01-27-2007 10:59 PM  12 years ago
Topic Vote0Post 1
andythilo

rrApprentice

Saffron Walden, Essex, UK

MyPosts All Forum Topic
Notchy 9254 - but no gears stripped?
Had problems with my 401/9254 combo today, tail would occasionally kick a little only a few degrees, but wasn't holding steady in a hover.

Decided to check it over tonight, found that the clutch was stuck for some reason, all sorted now, but while checking the tail linkage, I noticed that my 9254 is notchy, i.e as you rotate the servo wheel it makes a like tiny clicks. I've check the gears and their all fine, no lost teeth, so what could be the cause?

Should I just send it to Futaba, I wanted to send in the 401 anyway for checking.

Also anyone have any ideas how much it costs to look at these things? I'm not gonna pay silly money when a new combo is like £100.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 05:43 AM  12 years ago
firefox

rrApprentice

Thailand

MyPosts All Forum Topic
Had the same thing happen to me. Was checking over my heli and found that the tail control was very loud. It turned out to be the 9254, which had become very "rough". Took it apart, checked the gears, which were fine. Cleaned the potentiometer, no change.
SHARE  PM  EMAIL  Attn:RR  Quote
01-28-2007 08:58 AM  12 years ago
jadams

rrKey Veteran

East coast USA

MyPosts All Forum Topic
Send it back to Hobby Services, I just had my 9254 replaced because of the same exact problem. The servo felt like it had teeth missing from the gears and the tail would not hold. They replaced it for FREE.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 09:34 AM  12 years ago
andythilo

rrApprentice

Saffron Walden, Essex, UK

MyPosts All Forum Topic
Ok well I hope ripmax are as good as that here in the UK. I'll get both the servo and gyro posted off tommorow for checking.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 11:45 AM  12 years ago
Tday

rrKey Veteran

Needham, MA

MyPosts All Forum Topic
Hobby services is the warranty repair company for Futaba here in the colonies. Is ripmax the same thing for the UK.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 12:28 PM  12 years ago
andythilo

rrApprentice

Saffron Walden, Essex, UK

MyPosts All Forum Topic
Yes I believe so, Ripmax are the UK distributors for Futaba and their service agent too. I'll call them tommorow.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 05:52 PM  12 years ago
firefox

rrApprentice

Thailand

MyPosts All Forum Topic
Too bad the distributors in my country only say "we'll send it in for repair, you pay the cost". The word "Warranty" is somewhat foreign to them.
SHARE  PM  EMAIL  Attn:RR  Quote
01-29-2007 11:13 AM  12 years ago
andythilo

rrApprentice

Saffron Walden, Essex, UK

MyPosts All Forum Topic
Spoken to Ripmax today, well they say theirs nothing wrong with either the gyro or servo. They said that unless it was something they could replicate on the bench there was nothing they could do lol.

So oh well i've made some improvements on the rudder anyway, loosened up the wire joint and pitch slider so it's quite smooth and free now.

I'm gonna go back to single foam pad for mounting, change the servo horn so the limit is set right at 100.

See what happens then.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 620 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Servo - Gyro - Gov - Batt › Notchy 9254 - but no gears stripped?
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Thursday, November 21 - 10:54 am - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online