RunRyder RC
WATCH
 1 page 1333 views POST REPLY
01-27-2007 09:16 PM  12 years ago
Topic Vote0Post 1
J Kofoed

rrApprentice

Denmark

MyPosts All Forum Topic
T-REX 600 tail.
"
well it went right in yesterday...
the cause was a mechanical failure in the tail.
http://www.runryder.com/t259728p1/?highlight=tail+rotor
"
I think the new item from Align can be used on a 3DMP.
All that for only USD 16,-.

H60109:
●New tail rotor holder x 2
●New stainless steel tail rotor hub x 1(Φ10x39mm)
●Bearing MR105ZZ x 2(Φ5xΦ10x4mm)
●Thrust Bearing F5-10M x 2
●Washer x 2(Φ3xΦ8x0.6mm)
●M4 set screw x 1(M4x4mm)
●Socket screw x 2(M3x8mm)
●Sokcet collar screw x 2(M3x20mm)
●M3 nut x 2
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-27-2007 09:27 PM  12 years ago
falcon

rrKey Veteran

UK

MyPosts All Forum Topic
I upgraded the tail before i flew mine picture below.
i also fitted metal pulleys front and rear.
I had my first flight today and with the CSM720 gyro it was perfect.

www.m0kwr.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-30-2007 06:07 AM  12 years ago
bell-230

rrKey Veteran

sonoma, ca (currently milano italy)

MyPosts All Forum Topic
the t-rex 600tail rotor is still the same flawed design, the best replacements are the joker/robbe hubs(the new mini joker hub fits the best). a raptor hub would also work better than the t-rex 600 hub.ian brooke
k2shots.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-30-2007 10:03 AM  12 years ago
falcon

rrKey Veteran

UK

MyPosts All Forum Topic
T-rex 600tail rotor is still the same flawed design,
could you explain which part you are refering too.
www.m0kwr.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-30-2007 02:05 PM  12 years ago
Thuvanduc

rrApprentice

Salt Lake City, Utah

MyPosts All Forum Topic
I replaced mine with a Quick UK Raptor tail for $65, work perfect.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-30-2007 03:48 PM  12 years ago
bell-230

rrKey Veteran

sonoma, ca (currently milano italy)

MyPosts All Forum Topic
it's the design in which the bolt that holds the blade grip on, also acts as the shaft for the blade grip. in the case of the 3dmp, you could also just get a longer shouldered bolt that goes in all the way to the t/r shaft, this would greatly strengthen the bolt and make it just as likely to occur on the mp as it would be on a t-rex 600, or logo-14.

also the raptor tail is of the different design in which the bolt does not act as the shaft, it's a good design.
ian brooke
k2shots.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-30-2007 10:47 PM  12 years ago
J Kofoed

rrApprentice

Denmark

MyPosts All Forum Topic
Hi bell-230.
It is the upgraded tail rotor from Align: Look for H60109.

http://www.align.com.tw/shop/produc...roducts_id=1499

The bolt does not acts as the shaft. And the hub is made of AISI 304.
Synergy N9 has the same design.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-30-2007 11:59 PM  12 years ago
bell-230

rrKey Veteran

sonoma, ca (currently milano italy)

MyPosts All Forum Topic
ah ok they fixed it, i was going by the photo above and my friends t-rex 600.

and the new hub is the same style as the joker/robbe t/r and works well.
ian brooke
k2shots.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 1333 views POST REPLY
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Thursday, November 21 - 9:19 pm - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online