RunRyder RC
WATCH
 1 page 3170 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Servo - Gyro - Gov - Batt › CSM 720 servo frame rate
01-27-2007 04:44 PM  12 years ago
Topic Vote0Post 1
falcon

rrKey Veteran

UK

MyPosts All Forum Topic
CSM 720 servo frame rate
What frame rate can i run on a futaba 9254 or a JR 8700
www.m0kwr.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-27-2007 04:56 PM  12 years ago
TOSH

rrElite Veteran

UK.Peterborough

MyPosts All Forum Topic
8700g:
1520Us frame rate, and 4ms pulse rate

9251:
760Us Frame Rate and 3ms pulse rate

9253 / 9254:
1520Us frame rate and 3.5ms pulse rate
Flybars. Who needs `em.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-27-2007 05:30 PM  12 years ago
falcon

rrKey Veteran

UK

MyPosts All Forum Topic
Cheers Tosh
I have just upped the setting on my 9254
www.m0kwr.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-27-2007 05:33 PM  12 years ago
Colin Mill

rrVeteran

England

MyPosts All Forum Topic
Hi

Interestingly, we have found that, although the 401 only runs the 9253 or 9254 at 3.5ms these servos are actually capable of running at 3ms which is as fast as the 601/611 drive the 9251/9256 servos.

It makes you wonder what the 760us thing with the 9251 and 9256 was all about anyway

Colin (CSM)
SHARE  PM  EMAIL  Attn:RR  Quote
01-28-2007 01:23 PM  12 years ago
jsenicka

rrProfessor

Eagle River, WI

MyPosts All Forum Topic
Colin,
just mounted up my new 720 on one of the Rappy 90's. All I can say is wow. Super easy to configure and an amazing gyro. Went from an older G5000T with an 8700G to the 720 and 8700. Works fantastic.
Jim Senicka
Team Manager, GrandRC Flight Team
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 01:29 PM  12 years ago
Colin Mill

rrVeteran

England

MyPosts All Forum Topic
Hi Jim

Many thanks - I'm glad you like it!

Colin
SHARE  PM  EMAIL  Attn:RR  Quote
01-28-2007 07:52 PM  12 years ago
SRH990

rrKey Veteran

Birmingham, UK

MyPosts All Forum Topic
Colin,
I'm using a 720 with a 9254 servo on my Trex 600. I find that I'm getting a very slow wag which isn't related to gyro gain. At the moment the gyro is mounted to the metal plate, on 4 foam pads to the gyro mount area above the tail boom mount. I did try a firmer mounting for the gyro but ended up with a slow rotation I could only stop with trim, this was after running through the quick setup again and adjusting the pushrod length to give the right offset when in rate mode. The gyro is set with the servo parameters although at the 3.5ms pulse rate. Any ideas?
Steve -Trex 700N, Trex 600N, Raptor 550E, 450SE, Mini Titan, Logo 5003D, Beam E4
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 08:03 PM  12 years ago
falcon

rrKey Veteran

UK

MyPosts All Forum Topic
SRH990 what can i say, i am using the same set-up and its perfect but i am using the Quick uk tail push rod kit and mount + metal tail gearbox and pulleys (pic in my gallery)
I flew my Trex600and i honestly forgot all about the gyro did the quick setup at home set gain at 80% and flew it
www.m0kwr.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-28-2007 08:12 PM  12 years ago
TOSH

rrElite Veteran

UK.Peterborough

MyPosts All Forum Topic
Sounds like vibration, unlikly on a lecy tho. Check the push rod linkage is nice and free or even move the gyro somewhere else if you can.Flybars. Who needs `em.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2007 10:09 PM  12 years ago
Colin Mill

rrVeteran

England

MyPosts All Forum Topic
Hi SRH990

Have a quick check if the slow wag is also there in conventional mode or not. Slow wags that are not significantly gain dependant are usually linkage related. If the wag is in HL mode only then that will confirm that. Stick-slip friction at the hub bearings and/or 'give' or slop in the linkage are the causes of the effect. Bear in mind that the tail bearings will be under about 150lbs of tension which is way outside their design load so even seemingly perfect bearings can cause the problem and that, unless you have a pull like Geoff Capes its impossible to put them under a test load by hand.

Anyway, let me know how you get on in normal mode.

Best regards

Colin
SHARE  PM  EMAIL  Attn:RR  Quote
01-29-2007 08:57 AM  12 years ago
SRH990

rrKey Veteran

Birmingham, UK

MyPosts All Forum Topic
I've actually got a Quick UK tail fitted which has alloy blade grips and has thrust races fitted. I've had a quick look over and the movement is smooth enough but there is some slop in the linkages on the tail pitch yoke. I'll investigate this further and try normal mode, thanks.Steve -Trex 700N, Trex 600N, Raptor 550E, 450SE, Mini Titan, Logo 5003D, Beam E4
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-10-2008 06:30 PM  11 years ago
bill the greek

rrKey Veteran

Greece

MyPosts All Forum Topic
How much is the fps for the S9151 futaba servo and the pulse rate?

thanks,

Bill
Vasilis

Nobody is Perfect but who want to be Nobody...
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-10-2008 10:55 PM  11 years ago
3D Heli Ireland

rrVeteran

Ireland

MyPosts All Forum Topic
As a rule the Futaba tail servos generally run the shorter pulse length of 760us (short) and the higher servo frame rate of 333 fps. It is very nessecary to change these values as it simply won't work with the wrong pulse length and will not be optimal with the wrong frame rate.Skookum Robotics,Sav�x, Motors and Servos,Optipower,SwitchGlo,CML st
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
04-11-2008 08:19 PM  11 years ago
bill the greek

rrKey Veteran

Greece

MyPosts All Forum Topic
Thanks for reply,
im comfused because download the manual today of 14Mhz and say the S9151 run at 1520ms. If its true at 1520 what is the fps?

Thanks,

Bill
Vasilis

Nobody is Perfect but who want to be Nobody...
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-12-2008 10:45 PM  11 years ago
3dhiro

rrApprentice

Scotland

MyPosts All Forum Topic
All Futaba digital servos are capable of 333Hz.
S9251, S9256 and BLS251 are 760us. All other Futaba servos are 1520us.
SHARE  PM  EMAIL  Attn:RR  Quote
04-12-2008 11:45 PM  11 years ago
bill the greek

rrKey Veteran

Greece

MyPosts All Forum Topic
Thanks.
HZ and the frame rate its the same?
Bill
Vasilis

Nobody is Perfect but who want to be Nobody...
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-28-2008 07:23 PM  11 years ago
HFG

rrApprentice

Toronto, Canada

MyPosts All Forum Topic
Does the 1520us and 760us refer to center deflection or full deflection ?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-28-2008 07:37 PM  11 years ago
jsenicka

rrProfessor

Eagle River, WI

MyPosts All Forum Topic
centerJim Senicka
Team Manager, GrandRC Flight Team
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-28-2008 07:40 PM  11 years ago
HFG

rrApprentice

Toronto, Canada

MyPosts All Forum Topic
I am working on a servo tester at the moment and just started looking into frame rates and such. Anyone know of somewhere where i can find a summary of all the possible frame rates and pulse widths ?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 3170 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Servo - Gyro - Gov - Batt › CSM 720 servo frame rate
 Print TOPIC  Make Suggestion 

 6  Topic Subscribe

Wednesday, November 20 - 10:22 pm - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online