RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 561 views POST REPLY
HomeAircraftHelicopter
e-
Align
Other › Binding dx6?
11-27-2006 03:01 AM  11 years agoPost 1
hooked124

rrNovice

BC LA

My Posts: All  Forum  Topic

Hello all,
Been getting good info here, it helped get my 450sa off the ground! Now I would like to know how to bind the trans/recvr. The book says to plug in the bind lead, plug up a battery to an open port and a blue led should flash. All of my recvr ports are used, and when I do get the battery pluged up only the orange led blinks. Any thoughts / help!? Also any input on the following to make my sport flying better? Not ready for 3-D, yet.

Gregory

Trex 450sa
Spectrum dx 6 w/4 s75(s)
Align 430L 3550 w/ 13 tooth
Align 35 Amp BL ESC
Eflite G90 heading lock gyro
Align 11.1 v Battery

PM  EMAIL  Attn:RR  Quote
11-27-2006 03:17 AM  11 years agoPost 2
rky5

rrVeteran

Oak Hills california

My Posts: All  Forum  Topic

Use the batt port for the binding, That port should be open......because the ESC has a BEC circut built in, and there is no need for another batt to be plugged in to batt on the RX?
I have never seen a blue light ... mine is orange as well, I think the blue was an old version.

PM  EMAIL  Attn:RR  Quote
11-27-2006 03:23 AM  11 years agoPost 3
rky5

rrVeteran

Oak Hills california

My Posts: All  Forum  Topic

Also I noticed from your set up you are using the S75 servos that came with the radio?
I think the DX6 is a Great radio!! but the S75 servos I tried them and they developed so much slop in such a short time I had almost 1/8" slop. And then they tend to jitter after a very short time as well so my collective was jumping up and down.

They are good for smaller models but good for the Trex.
Just my 2 cents worth

PM  EMAIL  Attn:RR  Quote
11-27-2006 04:19 AM  11 years agoPost 4
hooked124

rrNovice

BC LA

My Posts: All  Forum  Topic

rky5,
Hey thanks for the info, it looks like I was not holding the bind button long enough. Dang short Army attention span and all! Anyway, yes I'm using the servos for now, plan on getting something better in the next week or so. And with that, your 2 cents is worth, oh, I'd say a few hundred or more!? This is not the setup I will be using when I get past the hover stage. Thanks again.

Gregeroy

CH-47D ??E?? FE!

PM  EMAIL  Attn:RR  Quote
11-27-2006 05:06 PM  11 years agoPost 5
rky5

rrVeteran

Oak Hills california

My Posts: All  Forum  Topic

Hey good luck!
And dont get me wrong I used the S75s they will work good for a while.
When you are ready I am using HS65s and an HS81 on the tail on both mine. And they work really great.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 561 views POST REPLY
HomeAircraftHelicopter
e-
Align
Other › Binding dx6?
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Saturday, June 23 - 3:44 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online