RunRyder RC
WATCH
 1 page 676 views POST REPLY
HomeAircraftHelicopterHIROBOOther › maybe just another dumb question?
11-23-2006 04:53 AM  11 years agoPost 1
ket

rrVeteran

ohio hill country

My Posts: All  Forum  Topic

sceadu and sceadu evo 50.. how do you tell them apart. I cant tell one piece of plastic from the next? is there a frame difference? color?

PM  EMAIL  GALLERY  Attn:RR  Quote
11-23-2006 08:25 AM  11 years agoPost 2
killerg

rrApprentice

Eastvale, California

My Posts: All  Forum  Topic

The EVOs has push pull on controls. Thats the only difference that I know of.
Graham

PM  EMAIL  GALLERY  Attn:RR  Quote
11-23-2006 09:48 AM  11 years agoPost 3
Jafa

rrElite Veteran

Sydney, Australia

My Posts: All  Forum  Topic

The head was significantly changed
The plastic used in the frames was also changed


Protos | Logo 400 & 500 | Sceadu Evo | Freya Evo | Trex600N | Avant FX

PM  EMAIL  GALLERY  Attn:RR  Quote
11-23-2006 05:56 PM  11 years agoPost 4
ket

rrVeteran

ohio hill country

My Posts: All  Forum  Topic

how was the head changed? is there any thing on frame that will tell if its evo 50 type plastic..? also I read some where about frame brace/supports that should be installed.. does anyone have a part number for these parts?.. I still need to figure out which servo's to use.. i've been told 3151 ae to slow.. I dont do 3d as fo yet.. but dont want heli to be super slow in response either..

PM  EMAIL  GALLERY  Attn:RR  Quote
11-23-2006 08:06 PM  11 years agoPost 5
mrNoodles

rrProfessor

Borlänge, Sweden

My Posts: All  Forum  Topic

The EVO head has the bladegrips with the pitcharms in the leading edge, and the Sceadu has trailing edge grips.

Below is a pic of a EVO head.

/Fredrik
'Hm now I just have to find out where to connect the GV1 sensor to the Jazz80 ESC.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-23-2006 10:05 PM  11 years agoPost 6
racer944

rrApprentice

Greely, Ontario - Canada

My Posts: All  Forum  Topic

Sure fire way to tell...
The EVO frames have the little extra plastic bump where the canopy standoff posts with the rubber tips are mounted (on top, ahead of the main rotor shaft). The standard non EVO frames are flat in that area (see photos below for the standard and EVO frames).

Cheers;
Eric

Sceadu

EVO

PM  EMAIL  Attn:RR  Quote
11-24-2006 01:24 AM  11 years agoPost 7
ket

rrVeteran

ohio hill country

My Posts: All  Forum  Topic

mrNoodles I don't totally know what you mean on leading edge grips.. wouldn't they just need to be flipped over , I'll probably figure it out when heli arrives.

I guess next question will be on what pipe to use.. I dont do 3D but still will be useing a hyper 50 because someday I might try some fancy tricks and things and dont want to need to up grade to stronger motor

PM  EMAIL  GALLERY  Attn:RR  Quote
11-24-2006 06:10 PM  11 years agoPost 8
mrNoodles

rrProfessor

Borlänge, Sweden

My Posts: All  Forum  Topic

Take a look at the picture in my post above.

/Fredrik
'Hm now I just have to find out where to connect the GV1 sensor to the Jazz80 ESC.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-24-2006 09:09 PM  11 years agoPost 9
bigblock

rrApprentice

sweden

My Posts: All  Forum  Topic

PM  EMAIL  GALLERY  Attn:RR  Quote
11-27-2006 12:07 AM  11 years agoPost 10
marc8090

rrElite Veteran

Long Island, N.Y.

My Posts: All  Forum  Topic

The two piece JK Hatori pipe is awesome. 3151's will be fine. They are not too slow for general sport flying. The original head had a short seesaw with long upper mixing arms where the link going up to the grip was on the back of the grip as the head rotates clockwise. The EVO head has a long seesaw with short mixing arms where the link goes to the front side of the grip.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 676 views POST REPLY
HomeAircraftHelicopterHIROBOOther › maybe just another dumb question?
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Wednesday, July 18 - 12:10 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online