RunRyder RC
WATCH
 1 page 748 views POST REPLY
HomeAircraftHelicopterRadio - Servo - Gyro - Gov - Batt › Futaba 9254 servo failure
11-20-2006 01:47 PM  11 years agoPost 1
dvdking

rrVeteran

Willingboro NJ

My Posts: All  Forum  Topic

Any one hearing that there was a bad batch of 9254 servo's that came out and people are having servo failure because of these bad servo's. I brought one and my servo just gave out. No response at all

PM  EMAIL  GALLERY  Attn:RR  Quote
11-20-2006 02:34 PM  11 years agoPost 2
ant_mb

rrElite Veteran

United States

My Posts: All  Forum  Topic

Jeff send it back for repair. There are many things that could caused it to fail, and without them checking it out you'll never know the cause. Is this the same servo that you changed the gear set in?

PM  EMAIL  GALLERY  Attn:RR  Quote
11-20-2006 02:39 PM  11 years agoPost 3
dgshaffer

rrElite Veteran

New Jersey

My Posts: All  Forum  Topic

I pulled it apart at the field thinking the gears may have been stripped. When I found outthat they weren't we put another servo in that spot on the receiver and then into the output on the gyro and it worked as it should.

This servo may have caused his MA to piro out of control that time it crashed.

PM  EMAIL  GALLERY  Attn:RR  Quote
11-20-2006 02:45 PM  11 years agoPost 4
ant_mb

rrElite Veteran

United States

My Posts: All  Forum  Topic

This servo may have caused his MA to piro out of control that time it crashed
Could be, but I thouhgt the low voltage reset the gyro? Could have also been damaged in the crash.

PM  EMAIL  GALLERY  Attn:RR  Quote
11-20-2006 06:23 PM  11 years agoPost 5
MichaelP

rrKey Veteran

Northumberland UK

My Posts: All  Forum  Topic

I use the 9254 in all my scalers and never had any problems at all.

http://www.webstarts.com/micksscalehelicopters

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-24-2006 02:49 AM  11 years agoPost 6
RCMed-x

rrVeteran

westpalmbeachflorida usa

My Posts: All  Forum  Topic

I have built over 100 helis not all with 9254 but never had
any problems as of yet with those that have them

PM  EMAIL  GALLERY  Attn:RR  Quote
11-24-2006 06:36 AM  11 years agoPost 7
meo_udon

rrNovice

Udonthani, Thailand

My Posts: All  Forum  Topic

I had 3 times for 9254 and last week I try to repair by remove gearbox and run 9254 by push a finger to pot he is reverse direction of motor. When I change new pot from 3001 to 9254 and test it. Work good but I found some crack about signal wire by I impact my servo to the gound many time. Arm 9254 is shake, I solder new to signal wire to resolve it, It work good for 4 flights ago. I am very happy now.

PM  EMAIL  HOMEPAGE  Attn:RR  Quote
WATCH
 1 page 748 views POST REPLY
HomeAircraftHelicopterRadio - Servo - Gyro - Gov - Batt › Futaba 9254 servo failure
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Sunday, July 22 - 7:49 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online