RunRyder RC
WATCH
 1 page 483 views POST REPLY
HomeRC & PowerAircraftHelicopterEngines Plugs Mufflers Fuel › bearing change on OS50
10-24-2006 03:24 PM  12 years agoPost 1
sewu

rrApprentice

94132

My Posts: All  Forum  Topic

The non-hyper version has a different carb than hyper one, between crankcase and carb, there is the Propeller nut, and it is very hard to pull it out, does anyone has a better way to do it ?

Thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 03:51 PM  12 years agoPost 2
Doug

rrElite Veteran

Port Saint Luice Florida....

My Posts: All  Forum  Topic

If you are refering to the "clamp screw" which holds the carb. just loosen it and twist the carb back and forth to remove.

First member of Member of Bearings Anonymous

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 05:02 PM  12 years agoPost 3
airdodger

rrElite Veteran

Johnston USA

My Posts: All  Forum  Topic

What Doug said, just want to clear up that it does not remove, it has a milled spot that fits around carb. Chris

Chris

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 05:40 PM  12 years agoPost 4
Doug

rrElite Veteran

Port Saint Luice Florida....

My Posts: All  Forum  Topic

Yes I should have mentioned that the screw just clamps the two pieces of the "lock" together they will come out once you remove the carb.

First member of Member of Bearings Anonymous

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 06:55 PM  12 years agoPost 5
zipphreak

rrApprentice

Attleboro, MA

My Posts: All  Forum  Topic

Another small tip with the carb clamp. After you loosen the screw in the clamp, but do not remove it, just give it a little push to separate the jaws of the clamp. Makes it a little easier in removing the carb, then just twist off the carb. DONE!

PM  EMAIL  Attn:RR  Quote
10-24-2006 08:06 PM  12 years agoPost 6
Doug

rrElite Veteran

Port Saint Luice Florida....

My Posts: All  Forum  Topic

Good point, as the "jaws" tend to get imbedded in the plastic insulator.

First member of Member of Bearings Anonymous

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 08:25 PM  12 years agoPost 7
sewu

rrApprentice

94132

My Posts: All  Forum  Topic

yes I am talking about the plastic insulator, when I need to heat up the crankcase to remove bearings, do I need to remove it ?Thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 08:36 PM  12 years agoPost 8
airdodger

rrElite Veteran

Johnston USA

My Posts: All  Forum  Topic

Take everything off the engine. Chris

Chris

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 09:24 PM  12 years agoPost 9
Doug

rrElite Veteran

Port Saint Luice Florida....

My Posts: All  Forum  Topic

Ther is a slightly better than even chance that the insulator will stay on the carb.

First member of Member of Bearings Anonymous

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 09:35 PM  12 years agoPost 10
sewu

rrApprentice

94132

My Posts: All  Forum  Topic

Doug

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 483 views POST REPLY
HomeRC & PowerAircraftHelicopterEngines Plugs Mufflers Fuel › bearing change on OS50
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Tuesday, December 11 - 9:41 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online