RunRyder RC
WATCH
 1 page 355 views POST REPLY
HomeAircraftHelicopter
e-
Align
Other › Servo mounting? And motor pinion?
10-24-2006 02:46 AM  12 years agoPost 1
biggame121

rrApprentice

OC, CA

My Posts: All  Forum  Topic

Hey guys,

I just bought a 450se v2 w/hs-65mg should they be mounted in the frame or outside I have seen both.

And also it came with 2 motor pinions 11 tooth and 12 tooth which is perfered fro just basic flight no 3D yet..

Thanx

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 03:05 AM  12 years agoPost 2
Jay Mowl

rrApprentice

Owosso Mi. USA

My Posts: All  Forum  Topic

I believe they mount set in the frame with servo mounting tabs and screws on the outside. This is the only way I have ever seen it done. 11th should be just fine.

PM  EMAIL  Attn:RR  Quote
10-24-2006 04:07 AM  12 years agoPost 3
kcass518

rrVeteran

Port Washington, NY - USA

My Posts: All  Forum  Topic

My HS-65mg's wouldn't fit through the cutouts, so I was advised to shave a little of the cutout away with an xacto knife. I did that, but subsequently decided to mount the servos from the inside, anyway. They fit better and were easier to screw in. Of course, the elevator servo gets mounted with the works on the outside of the frame and the servo arm in the centerline of the frame. Hope this helps.

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 04:43 AM  12 years agoPost 4
biggame121

rrApprentice

OC, CA

My Posts: All  Forum  Topic

Thanx guys that is what I was hoping because I had allready mounted the servos then I decided to look @ some old threads and people had them on the outside.

PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2006 10:05 AM  12 years agoPost 5
phillips942

rrApprentice

San Diego, CA

My Posts: All  Forum  Topic

What size mini servos are you using anyways??? That makes a big difference...

Using the HS-56's... The Aft Servo shoud be mounted from the left side (if you were inside the heli) with the output shaft facing aft also... when you put the servo arm on it will line up with the swash ball.

The second servo will go bottom right and installed from the inside of the frame to the outside with the output shaft facing forward.

The Last servo will go Top Left and also installed from the inside etc....

Im not sure which servo goes in which channel because im not at my workbench but i can tell you that's the right setup...

Hope that helped...lol

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 355 views POST REPLY
HomeAircraftHelicopter
e-
Align
Other › Servo mounting? And motor pinion?
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Sunday, December 16 - 12:58 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online