RunRyder RC
WATCH
 1 page 615 views Post Reply
Home✈️Aircraft🚁HelicopterCentury Radikal G20-30 N640 Hawk Predator › 30/50 front rudder servo setup
09-06-2006 04:27 AM  14 years ago
Topic Vote0Post 1
Gearhead

rrMaster

Vt

MyPosts All Forum Topic
30/50 front rudder servo setup
hi guys,,

for you guys that are running your rudder servo up front on your 30's & 50's I'm just wondering what you are using for a bellcrank and crank-mount,, photos please if you will, and tell all, and what/where you got your tubing,,,

I have always use the rear servo mount with the stock linkage with never a complaint, my servo remained dry do to that I run a Weston pipe (it's exhaust points straight down between the struts), but I may change pipes so I will want to move my servo up front, plus I'm sure it will help with the balance,,

reps are welcome to reply too..

thanks guys !!
Jim
Jim
Buzz Buzz Buzz
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-06-2006 05:23 PM  14 years ago
jackheli

rrProfessor

Vancouver - Canada

MyPosts All Forum Topic
Check my gallery. Full set of pictures.It's easy to find an excuse to do wrong. Hard is not to find an excuse to do right.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-06-2006 07:17 PM  14 years ago
Gearhead

rrMaster

Vt

MyPosts All Forum Topic
thanks, I was wondering if I could use a bellmixer for a bellcrank,, now, what did you use for tubing?

Jim
Jim
Buzz Buzz Buzz
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-06-2006 07:18 PM  14 years ago
jackheli

rrProfessor

Vancouver - Canada

MyPosts All Forum Topic
http://www.heli-world.com/detail.aspx?ID=3213It's easy to find an excuse to do wrong. Hard is not to find an excuse to do right.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-06-2006 10:35 PM  14 years ago
Gearhead

rrMaster

Vt

MyPosts All Forum Topic
thanks !!

Jim
Jim
Buzz Buzz Buzz
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-06-2006 11:20 PM  14 years ago
SteveH

rrProfessor

Texas

MyPosts All Forum Topic
I used a Bell mixer, a plastic one that I had replaced on the heli with aluminum, and a section of an old bent lower main frame. Works good.

The pushrod tubing is generic carbon fiber pushrod from the LHS.

The government cannot give you anything without first taking it from someone else.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-08-2006 08:14 PM  14 years ago
Gearhead

rrMaster

Vt

MyPosts All Forum Topic
well thanks guys, I thought there was more guy that did this but I guess therrr is only 2 of yeea's,, all I need is the tubing..

Jim
Jim
Buzz Buzz Buzz
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-08-2006 09:12 PM  14 years ago
jackheli

rrProfessor

Vancouver - Canada

MyPosts All Forum Topic
And then there were three... GenesisIt's easy to find an excuse to do wrong. Hard is not to find an excuse to do right.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-08-2006 09:20 PM  14 years ago
Gearhead

rrMaster

Vt

MyPosts All Forum Topic
LOLJim
Buzz Buzz Buzz
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-13-2006 01:53 PM  14 years ago
MidStar40

rrApprentice

Sioux Falls, SD

MyPosts All Forum Topic
Thanks for the ideas guys, I copied you - now there's four.

Rod
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-13-2006 03:16 PM  14 years ago
BC Don

rrElite Veteran

Calgary, AB Canada

MyPosts All Forum Topic
Steve H., what in the heck is that setup? You've got a CCPM setup but instead of doing the direct link like the Raven you are using the front Servo tray! Is that something you've "made up" or is / was that something direct from Century.

In any case, it looks pretty cool / flyable and I'm wondering if I should do the same thing on my Hawk. I'd be interested in comments you have about it - how does it fly compared to the normal Hawk Setup, what is the servo requirements etc.
Got Money? Send it to me, I'm a Heli Addict.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
09-13-2006 05:26 PM  14 years ago
jackheli

rrProfessor

Vancouver - Canada

MyPosts All Forum Topic
BC DON

Check my gallery and
http://www.runryder.com/t195448p1/
http://www.runryder.com/t272962p1/?
It's easy to find an excuse to do wrong. Hard is not to find an excuse to do right.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 615 views Post Reply
Home✈️Aircraft🚁HelicopterCentury Radikal G20-30 N640 Hawk Predator › 30/50 front rudder servo setup
Print TOPIC

 4  Topic Subscribe

Friday, November 27 - 11:19 pm - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online