RunRyder RC
WATCH
 1 page 868 views Post Reply
07-19-2006 05:32 PM  14 years ago
Topic Vote0Post 1
QuantumPSI

rrElite Veteran

Atlanta, GA

MyPosts All Forum Topic
Turbo cooling fan...
When will this be back in stock?

Mikel
...now where was I, dh/dt = BS-dx/dt
I will fly you forever... till earth do us part
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-19-2006 07:37 PM  14 years ago
oldfart

rrProfessor

Vancouver, Canada

MyPosts All Forum Topic
I do not know which one you are refering to.

The CN2202 version has been discontinued for awhile and is replaced by the new CN2202A.

I know they have not had the CN2202 for awhile but we did get the new CN2202A the last time we ordered them.

Phil Noel
Leisure-Tech Products
Distributing Century to Hobby Shops across Canada
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-19-2006 09:16 PM  14 years ago
Buzzin Brian

rrProfessor

College Station, Texas

MyPosts All Forum Topic
Are the new ones now comming with the start shaft with hex?Build it, fly it, crash it. Repeat as often as needed.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-19-2006 09:29 PM  14 years ago
marked23

rrKey Veteran

Lynnwood, WA

MyPosts All Forum Topic
I would use the HI3009. There's nothing wrong with the plastic fan. It's cheap and it works.

-Mark
SHARE  PM  EMAIL  Attn:RR  Quote
07-19-2006 09:36 PM  14 years ago
oldfart

rrProfessor

Vancouver, Canada

MyPosts All Forum Topic
Brian,

No, they came with the one way bearing built into the center of the fan & no instructions.

One is supposed to remove the two start shaft bearings from the two bearing blocks, then reinstall the bearing blocks to insure the integrity of the front frames.

Then one has to remover the start wand shaft from the hub and reinstall it with the hex at the starter end & the round part at the lower end.

When starting the engine, this round end is the part of the wand that is now inserted through the two former bearing blocks, and into the one-way bearing in the center of the fan. When the engine starts then the wand can be pulled out.

A lot easier to do then to explain. The ones we received did not come with instructions so many have been confused on receipt of them. Hopefully they have now included instructions. It would make things a lot easier for te customer to understan how it works.

I have explained the procedure to our Canadian dealers who have ordered them.

Phil Noel
Leisure-Tech Products
Distributing Century to Hobby Shops across Canada
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-19-2006 10:08 PM  14 years ago
oldfart

rrProfessor

Vancouver, Canada

MyPosts All Forum Topic
Marked23,

I agree, I have literally thousands of flights on the H13009 plastic units over the past 10 years on my various Hawks, Ravens, & Falcons.

I have never found reason to need to change.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-19-2006 10:10 PM  14 years ago
QuantumPSI

rrElite Veteran

Atlanta, GA

MyPosts All Forum Topic
I was talking about the new fan that's available...

Mikel
...now where was I, dh/dt = BS-dx/dt
I will fly you forever... till earth do us part
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-20-2006 10:57 AM  14 years ago
RevGadget

rrVeteran

Decatur, Alabama

MyPosts All Forum Topic
I don't know about re-stock, but no more plastic for me!

http://www.centuryheli.com/support/...tml?currentid=2

3D2me= One eye on the Tx, one on the Heli and my thumbs in between.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-20-2006 12:12 PM  14 years ago
SteveH

rrProfessor

Texas

MyPosts All Forum Topic
Phil,

An alternative to the installation/start procedure you explain is to use the Predator start shaft in the existing bearing blocks with the bearings and hex adapter with the new aluminum fan. The result is smooth starting with the use of your existing hex starting wand.
The government cannot give you anything without first taking it from someone else.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-20-2006 04:53 PM  14 years ago
oldfart

rrProfessor

Vancouver, Canada

MyPosts All Forum Topic
Your correct Steve, that will work also. I would just suggest that one uses two of the collars from the previous system to hold the shaft in a preset vertical position whereby it is held from bootoming in the fan one-way.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-20-2006 04:57 PM  14 years ago
QuantumPSI

rrElite Veteran

Atlanta, GA

MyPosts All Forum Topic
what's to stop that top piece from coming off during flight?

mikel
...now where was I, dh/dt = BS-dx/dt
I will fly you forever... till earth do us part
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-20-2006 05:01 PM  14 years ago
oldfart

rrProfessor

Vancouver, Canada

MyPosts All Forum Topic
The thicker end machined into the bottom.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 868 views Post Reply
Print TOPIC

 5  Topic Subscribe

Sunday, June 20 - 10:15 am - Copyright © 2000-2021 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online