RunRyder RC
WATCH
 1 page 595 views Post Reply
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Servo - Gyro - Gov - Batt › Schulze isl 6-330d error help ASAP
07-17-2006 12:33 PM  14 years ago
Topic Vote0Post 1
Kristjan

rrApprentice

Estonia, Tallinn

MyPosts All Forum Topic
Schulze isl 6-330d error help ASAP
Hi!

I haven`t been using my isl 6-330d for a long time and today I started charging 6S3P LiPos and an error message was displayed:

b2 overvoltage

It is version 8.04 so max 11S is possible.
Where is the problem??
Const. supply of 13.8V is provided 100%

Please give advice as soon as possible.

K.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-17-2006 12:56 PM  14 years ago
Dr Lodge

rrElite Veteran

Guildford, Surrey - UK

MyPosts All Forum Topic
Sounds like you might have setup the charger for 5S or similar - b2 is battery 2 or output 2, its saying its seeing more voltage than it should on this terminal (IIRC)Vibe 90, Vibe 50, Vigor CS x2,
Dyna-x, Knight 503D, Logo 10,
TRex 500, Furion, Gaui EP200
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-17-2006 01:01 PM  14 years ago
Kristjan

rrApprentice

Estonia, Tallinn

MyPosts All Forum Topic
Thanks but it`s not the cause.

I even tried setting for 7S (actually charging 6S) but still the same problem.

K.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-17-2006 01:19 PM  14 years ago
Paul Woodcock

rrElite Veteran

Dubai - United Arab Emirates

MyPosts All Forum Topic
Hi Kristjan

I have just gone to check my instructions and am also confused...

The only thing mentioned repetedly is that the charger doesn't like power supplies...try a car battery and see what happens.

What current rating is your power supply ?

6s is going to up the v from 13,8 and must need quite a high current capability...

Paul
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-17-2006 01:29 PM  14 years ago
Kristjan

rrApprentice

Estonia, Tallinn

MyPosts All Forum Topic
Good point but already tried it.

I tried using a car battery but still the same problem.

My power supply rates 10-12 amps so it is enough.
It must be the Schulze charger that`s causing the problems???

Ps. I read from the manual that if the supply voltage goes below 13.8V then it might cause problems. If it is 13.8 const (as is mine) then it`s OK.

K.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-17-2006 01:46 PM  14 years ago
z11355

rrMaster

New England

MyPosts All Forum Topic
lets go back to basics.

you've connected the 6S3P battery to the 6-330D LEFT side connectors, right?

the RIGHT side connectors are the B2 channel and that is limited
to 3S.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-17-2006 01:48 PM  14 years ago
Kristjan

rrApprentice

Estonia, Tallinn

MyPosts All Forum Topic
No I connected it on b2!

If I connected it to b1 then it wouldn`t error on b2.

b1 is left
b2 is right

b1 is not for LiPo`s

K.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-17-2006 01:58 PM  14 years ago
Dr Lodge

rrElite Veteran

Guildford, Surrey - UK

MyPosts All Forum Topic
The left side is where you want to connect. What makes you think B1 is not for LiPos?Vibe 90, Vibe 50, Vigor CS x2,
Dyna-x, Knight 503D, Logo 10,
TRex 500, Furion, Gaui EP200
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-17-2006 02:00 PM  14 years ago
Kristjan

rrApprentice

Estonia, Tallinn

MyPosts All Forum Topic
The manual?

It doensn`t say anything about LiPos in b1 chapers.

If you say that is it, then I`ll connect to b1.

K.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-17-2006 02:01 PM  14 years ago
z11355

rrMaster

New England

MyPosts All Forum Topic
b1 is not for LiPo`s
WRONG

You do not know what your charger is capable of to make that
statement. B1/Akku1 IS for all battery types and is the primary
output.

See section 8.1.1 of the manual (Battery output 1, Fixed C)
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-17-2006 02:05 PM  14 years ago
Kristjan

rrApprentice

Estonia, Tallinn

MyPosts All Forum Topic
Problem solved.

Thanks and case closed.

10 points to you all.

K.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 595 views Post Reply
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Servo - Gyro - Gov - Batt › Schulze isl 6-330d error help ASAP
Print TOPIC

 3  Topic Subscribe

Thursday, June 17 - 3:06 am - Copyright © 2000-2021 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online