RunRyder RC
WATCH
 1 page 638 views POST REPLY
HomeAircraftHelicopter
e-
Mikado
Other › Logo 14 rotorhead assembly : page 46
10-10-2005 11:00 AM  12 years agoPost 1
JEY

rrNovice

Paris

My Posts: All  Forum  Topic

I read from Lorents that on page 46 of logo manual, we have to use only one dampening #2756 ring on each side of the axis instead of 2 on each side like in manual. Just wanted to be sure. I don't fly 3D yet.

I read also is not needed to use outer washers #2016 on each side of axis, because this prevents the big screw to penetrate well enough in the axis. What about this ?

PM  EMAIL  GALLERY  Attn:RR  Quote
10-10-2005 12:24 PM  12 years agoPost 2
Lorents

rrElite Veteran

Oslo, Norway

My Posts: All  Forum  Topic

Hi Jey,

I have not said anything about the damper rings
Edit: #2756 = 3D O-ring Set Logo 10

Is this what you are reffering to?:
On page 43 in my manual the drawing shows two washers (#841) installed between the thrust bearing and the bearings inside the grips - that is a total of four washers, two on each side. But only one washer is to be used on each side. I downloaded a manual from the net, and this manual is updated on this page.
It could be that Mikado removed one pair of 841's so that you dont have to remove the 2016's. If you download a new manual from http://www.mikado-heli.de/files/eng..._logo14_6mb.pdf you will se that page 43 is revised.



What comes around goes around.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
10-10-2005 03:09 PM  12 years agoPost 3
JEY

rrNovice

Paris

My Posts: All  Forum  Topic

I was refering to that :

On page 43 in my manual the drawing shows two washers (#841) installed between the thrust bearing and the bearings inside the grips - that is a total of four washers, two on each side. But only one washer is to be used on each side. I downloaded a manual from the net, and this manual is updated on this page.

You are right, I mixed up part #841 in your text and damp rings, sorry.

PM  EMAIL  GALLERY  Attn:RR  Quote
10-10-2005 08:45 PM  12 years agoPost 4
Lorents

rrElite Veteran

Oslo, Norway

My Posts: All  Forum  Topic

No problem

Are you finished with your Logo soon?



What comes around goes around.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
10-11-2005 07:58 PM  12 years agoPost 5
JEY

rrNovice

Paris

My Posts: All  Forum  Topic

Not yet but the main parts are almost ready. I have no teflon grease yet, I assume, it is not so important if don't put grease on thrust bearings ?

PM  EMAIL  GALLERY  Attn:RR  Quote
10-11-2005 08:36 PM  12 years agoPost 6
mudbogger2

rrKey Veteran

Hoschton,Ga.

My Posts: All  Forum  Topic

It is very important to grease the thrust bearings!!!!!!!!!

They have a large load placed on them in flight and will seize if they are not greased.

Jon Jennings

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 638 views POST REPLY
HomeAircraftHelicopter
e-
Mikado
Other › Logo 14 rotorhead assembly : page 46
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Tuesday, July 17 - 1:01 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online