RunRyder RC
WATCH
 1 page 669 views POST REPLY
HomeAircraftHelicopterRadio - Servo - Gyro - Gov - Batt › TJ Pro Magnets Question
05-04-2005 08:42 PM  13 years agoPost 1
mcoccia

rrKey Veteran

Central Jersey

My Posts: All  Forum  Topic

Hi,

Will the GV1 magnets work in place of the MA one's?


Thanks
Mark

PM  EMAIL  GALLERY  Attn:RR  Quote
05-04-2005 09:26 PM  13 years agoPost 2
DOKEY

rrProfessor

Northamptonshire UK

My Posts: All  Forum  Topic

Yes

Ryan.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 669 views POST REPLY
HomeAircraftHelicopterRadio - Servo - Gyro - Gov - Batt › TJ Pro Magnets Question
05-04-2005 09:52 PM  13 years ago •• Post 3 ••
R/C Speed Nut

rrVeteran

Galesburg, Michigan USA

My Posts: All  Forum  Topic

I think the TJ just uses opposite polarity, so check that the sensor picks up the magnet.


Mike

Funky Chicken?!!..........I thought this was how you do a piro flip!!

PM  EMAIL  GALLERY  Attn:RR  Quote
05-04-2005 11:30 PM  13 years agoPost 4
Al Magaloff

rrMaster

12,199 Posts- Enough Time Wasted. See Ya!

My Posts: All  Forum  Topic

In fact, the directions have a statement about GV1 magnets, and which way to roll the sensor ( writing down for GV1, writing up for TJ magnet).

PM  EMAIL  Attn:RR  Quote
05-05-2005 12:31 AM  13 years agoPost 5
JuanRodriguez

rrProfessor

The Villages, Florida

My Posts: All  Forum  Topic

Gee, Al.....

Why bother reading the directions ???

PM  EMAIL  GALLERY  Attn:RR  Quote
05-05-2005 06:50 PM  13 years agoPost 6
mcoccia

rrKey Veteran

Central Jersey

My Posts: All  Forum  Topic

Hi,

I had asked the question before I even opened the package I did see in there last night after I installed the unit.


Thanks everyone

Mark

PM  EMAIL  GALLERY  Attn:RR  Quote
05-06-2005 12:08 AM  13 years agoPost 7
JuanRodriguez

rrProfessor

The Villages, Florida

My Posts: All  Forum  Topic

When all else fails, read the directions !!!

PM  EMAIL  GALLERY  Attn:RR  Quote
05-06-2005 05:39 AM  13 years agoPost 8
Ron Henry

rrApprentice

Atlanta area, GA - USA

My Posts: All  Forum  Topic

Radio's hack rare earth magnets work well. That's what I'm using in my machine

- Ron Henry
http://kaizenrc.com/forum

PM  EMAIL  GALLERY  Attn:RR  Quote
05-06-2005 07:11 AM  13 years agoPost 9
Wa11banger

rrElite Veteran

Huntsville, Al

My Posts: All  Forum  Topic

The difference is only in the polarity.. If you already have a magnet in the fan setup for use with a GV-1 there is no need to try and hack it out of there, just run the sensor writing down. If you have a clean fan (no mags) install the sensor with writing up and set the polarity of the magnets accordingly.. I usually run two magnets in each fan just for cheating balancing and that I can run either governor if I decide to switch. The one caveat (SP) to running the hall sensor with the writing down is it's not as sensitive. Still works fine but the clearance distance can be picky...

Just my .02
Rick

Proud member of the Quick UK, Duralite Flight Systems, V-Blade, & KBDD team

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-06-2005 06:56 PM  13 years agoPost 10
mcoccia

rrKey Veteran

Central Jersey

My Posts: All  Forum  Topic

Yesterday I had installed the TJ PRO but with the optical sensor instead. The unit works like a champ I'll save the magnets for my other fan that I am trying to balance out. This is the first time I am using a Gov..I am very impressed with the technology.


From what I understand the Futaba GV1 is slower than the MA TJ, is this true?

PM  EMAIL  GALLERY  Attn:RR  Quote
05-06-2005 11:54 PM  13 years agoPost 11
Al Magaloff

rrMaster

12,199 Posts- Enough Time Wasted. See Ya!

My Posts: All  Forum  Topic

Yes, true. The TJ with DS servo is a good all around set-up.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 669 views POST REPLY
HomeAircraftHelicopterRadio - Servo - Gyro - Gov - Batt › TJ Pro Magnets Question
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Tuesday, August 21 - 7:02 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online