RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 601 views POST REPLY
HomeAircraftHelicopterJR Heli Vibe 90/50, Sylphide 90, GSR260 › where to get aluminum mixing lever set for ergo 60 sport
11-07-2004 02:38 PM  13 years agoPost 1
greatplanes

rrApprentice

boston, ma

My Posts: All  Forum  Topic

i want to replace the stock plastic mixing lever set with the after market aluminum set
can any one give me part number and where to get? also need part number for aerobatic flybar and paddles
thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
11-07-2004 05:15 PM  13 years agoPost 2
Ivan

rrVeteran

Wichita

My Posts: All  Forum  Topic

I assume you mean the ones that bolt to the washout huband have the grey y-links that go to the swash....

You should be able to give Rick's a call and they would know the numbers for the mixing levers. FWIW I just put some bearings from ricks in my plastic levers. Just push out the brass bushings and put some flanged bearings in them (ala Vigor). You could probably just use the vigor partnumber as well.

Also as far as paddles, Just get yourself a set of V-Paddles (rick's will have them too) and you will be amazed at what your ergo can do. That was probably the single most satisfying upgrade I made to my Ergo(s). They are VERY AGGRESSIVE paddles, so if you aren't ready for that, get some flybar weights and start with them about half way out, or start with about 30% expo, I think I run about that.

The Ergo has a pretty soft flybar, so you can replace it with about any 4mm flybar. I used MA flybars on mine, they seemed to have a tad more "spring" to them, without being brittle.

Ivan

Back to it!

PM  EMAIL  Attn:RR  Quote
11-07-2004 05:44 PM  13 years agoPost 3
greatplanes

rrApprentice

boston, ma

My Posts: All  Forum  Topic

actually i may have used the wrong part name. i`m looking for the aftermarket version of the mixer arm set ? the 3 levers that the roll ,pitch, etc servos connect to, to move the swash plate up , down, side to sid etc
i do not know the corrcet name of this part. it replaces the 3 plastic levers { i saw one purple anodized} that supposedly removes the slop out if the mixing set up

PM  EMAIL  GALLERY  Attn:RR  Quote
11-08-2004 01:09 AM  13 years agoPost 4
Chuck Bole

rrElite Veteran

Tulsa Ok. U.S.A.

My Posts: All  Forum  Topic

try r/c helis plus under ksj http://www.rchelisplus.com/ but if they have bushings in them now thats where your slop is coming from, also cause glitches. like ivan said just put in flanged bearings the std vigor uses a small spacer in between the bearings .

chuck

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-10-2004 12:21 AM  13 years agoPost 5
Ivan

rrVeteran

Wichita

My Posts: All  Forum  Topic

I would suggest looking for the same parts from a Vigor standard. They should have been ball raced and were the same as the Ergo.

Back to it!

PM  EMAIL  Attn:RR  Quote
11-16-2004 05:07 PM  13 years agoPost 6
Yogi 1

rrApprentice

Clinton,CT USA

My Posts: All  Forum  Topic

You can get 5X8mm flanged Ball Bearings that will fit the stock plastic arms and all other areas also. Just push out the brass bushings and replace with BBs. I only had to file down the aluminum head arms to maintain the proper thickness. For the cost of a one set of (2) arms you can BBearing up the whole chopper. Ricks has these bearings available. Good Luck Yogi

Velocity Is A State Of Grace Get Some Now !

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 601 views POST REPLY
HomeAircraftHelicopterJR Heli Vibe 90/50, Sylphide 90, GSR260 › where to get aluminum mixing lever set for ergo 60 sport
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Saturday, June 23 - 5:37 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online