RunRyder RC
 7  Topic Subscribe
WATCH
 1 page 633 views POST REPLY
HelicopterMain Discussion › One bolt stripped in head align 91hp hope to save!
03-09-2018 02:54 PM  78 days agoPost 1
wifeorheli

rrElite Veteran

reno, nevada usa

My Posts: All  Forum  Topic

noticed a little fuel dripping from head of my 91hp. 1 of the 6 bolts in the engine block stripped. Used motor I think screw used was to small. Any chance of saving crank case? Sux over one head screw. Motor runs fine and doesn't lean but obviously loosing power. Any suggestions? Thanks

Novarossi Motors U.S.A
www.PLanethobby.com
Team GrandRc.com
Team Byron Fuels
ZRC U.S.A. "PushGlo, SwitchGlo"

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
03-09-2018 03:17 PM  78 days agoPost 2
JLF92677

rrApprentice

Southern California

My Posts: All  Forum  Topic

I believe the head bolts are 3mm. I would try tapping a new thread for 3.5mm bolt.

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2018 03:24 PM  78 days agoPost 3
Craig G.

rrNovice

Central NC

My Posts: All  Forum  Topic

Look into a helicoil repair (no pun intended).

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2018 04:59 PM  78 days agoPost 4
helitom

rrApprentice

Pine Grove, Calif, USA

My Posts: All  Forum  Topic

Look in the classified section of the AMA rag. I'm pretty sure Clarence Lee still does helicoil repairs. Prolly in the $25 range.

The older I get, the fewer things seem worth waiting in line for.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
03-09-2018 05:26 PM  78 days agoPost 5
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

Clarence does glow plug thread repairs. I can do it if you find no one willing to help you.

Ben Minor

Peak Aircraft/Team Minicopter Team Futaba Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2018 05:34 PM  78 days agoPost 6
TMoore

rrMaster

Cookeville, TN

My Posts: All  Forum  Topic

The head bolts are 3.5mm. Get a 3.5mm tap, clean out the threads and get the right bolt. If it's really hosed, it needs to be helicoiled.

Delayed Response Operator Not Engaged
AMA SECTION 336 = Good
Drones = EVIL

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
03-09-2018 05:47 PM  78 days agoPost 7
w8qz

rrVeteran

Grand Rapids, MI - USA

My Posts: All  Forum  Topic

DIY approach:
https://www.mcmaster.com/#helicoils/=1bwb2h4

It's really not that hard to do, if you're comfortable with basic machine shop work. A helicoil repair requires that there's enough material around the hole to handle the drill and STI tap, and still have a reasonable wall thickness

"The helicopter is much easier to design than the aeroplane, but is worthless when done."

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2018 09:27 PM  78 days agoPost 8
JuanRodriguez

rrProfessor

The Villages, Florida

My Posts: All  Forum  Topic

Though I’ve used helicoils many times over the years, a good alternative in this case might be to go with the bigger bolt and re-tap the buggered up thread. Perhaps the next bigger dimensionally sized American thread might be appropriate......

Been there, done that and old enough to know better.....

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2018 10:17 PM  78 days agoPost 9
Professor Fate

rrKey Veteran

Goose Creek S.C.

My Posts: All  Forum  Topic

Here's an idea... just replace the crankcase.

Welcome my son, Welcome to the machine

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2018 10:51 PM  78 days agoPost 10
ICUR1-2

rrElite Veteran

Ottawa, Ontario

My Posts: All  Forum  Topic

JuanRodriguez
Though I’ve used helicoils many times over the years, a good alternative in this case might be to go with the bigger bolt and re-tap the buggered up thread. Perhaps the next bigger dimensionally sized American thread might be appropriate......
Definitely a better option.
Color the bolt so you remember which one goes where.

spending time, paying attention

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2018 12:45 AM  78 days agoPost 11
Jeff polisena

rrElite Veteran

westpalmbeachflorida usa

My Posts: All  Forum  Topic

Try longer bolt , sometimes there are more threads to bite at the bottom . . With head off put fresh bolt in stripped hole and see if there is clean threads at the bottom .

I stole it ,flew it and gave it back ;)

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2018 11:34 AM  77 days agoPost 12
Heli_Splatter

rrElite Veteran

USA

My Posts: All  Forum  Topic

I would go with retaping the hole with a step up in size. I just don’t think helicoil is the answer for this case. You might even get away with green or red locktight after clamping head down.

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2018 12:31 PM  77 days agoPost 13
mr dan

rrVeteran

Stockton Calif

My Posts: All  Forum  Topic

Geeze! A crank case is less than $120.00. You’re a grandrc pilot why don’t you just get a new one?

"R.I.P Roman" Citizen 0094 in the Nation

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2018 01:24 PM  77 days agoPost 14
JuanRodriguez

rrProfessor

The Villages, Florida

My Posts: All  Forum  Topic

mr dan
Geeze! A crank case is less than $120.00. You’re a grandrc pilot why don’t you just get a new one?
Because it's silly to spend $120 for something that can easily be repaired at a fraction of the cost.....

Been there, done that and old enough to know better.....

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2018 02:23 PM  77 days agoPost 15
mr dan

rrVeteran

Stockton Calif

My Posts: All  Forum  Topic

Sponsored pilots don’t pay retail

"R.I.P Roman" Citizen 0094 in the Nation

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2018 05:02 PM  77 days agoPost 16
JuanRodriguez

rrProfessor

The Villages, Florida

My Posts: All  Forum  Topic

mr dan
Sponsored pilots don’t pay retail
While you may not, many of us enjoy making such repairs as an extension of the hobby....specially such an easy repair....

Been there, done that and old enough to know better.....

PM  EMAIL  GALLERY  Attn:RR  Quote
03-10-2018 06:36 PM  77 days agoPost 17
Jeff polisena

rrElite Veteran

westpalmbeachflorida usa

My Posts: All  Forum  Topic

I’ve seen people put paper clip in hole and put screw in and it holds . Hammer clip flat and thin and force head screw in . Get you some time out of it then buy new one .

I stole it ,flew it and gave it back ;)

PM  EMAIL  GALLERY  Attn:RR  Quote
03-11-2018 09:39 AM  76 days agoPost 18
wifeorheli

rrElite Veteran

reno, nevada usa

My Posts: All  Forum  Topic

Mr dan yes I am but why buy a new one if I can fix this one?!

Novarossi Motors U.S.A
www.PLanethobby.com
Team GrandRc.com
Team Byron Fuels
ZRC U.S.A. "PushGlo, SwitchGlo"

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 633 views POST REPLY
HelicopterMain Discussion › One bolt stripped in head align 91hp hope to save!
 Print TOPIC  Make Suggestion 

 7  Topic Subscribe

Sunday, May 27 - 2:08 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online