RunRyder RC
 3  Topic Subscribe
WATCH
 1 page 173 views POST REPLY
HelicopterFlybarless Rotor Head SystemsBrain iKon › Non heading hold
01-23-2018 01:13 AM  27 days agoPost 1
nappyroots2182

rrElite Veteran

Moline, il

My Posts: All  Forum  Topic

I found 2 places in the software that say heading hold with its boxed check marked. But I cant seem to get it to uncheck so I can do a mechanical trim flight on the tail

PM  EMAIL  GALLERY  Attn:RR  Quote
01-23-2018 01:26 AM  27 days agoPost 2
ICUR1-2

rrElite Veteran

Ottawa, Ontario

My Posts: All  Forum  Topic

You lower the gyro gain to get into rate mode. It goes into HH when the unit sees over 45%

spending time, paying attention

PM  EMAIL  GALLERY  Attn:RR  Quote
01-23-2018 01:39 AM  27 days agoPost 3
nappyroots2182

rrElite Veteran

Moline, il

My Posts: All  Forum  Topic

Ok ill give it a try tomorrow. Just figured I could of unchecked the box but doesn't look that way

PM  EMAIL  GALLERY  Attn:RR  Quote
01-23-2018 12:21 PM  27 days agoPost 4
nappyroots2182

rrElite Veteran

Moline, il

My Posts: All  Forum  Topic

Played with it this morning. I was given the heli and the program off a sd card so it was setup different then I'm used to. He was using the gyro screen and had a 3 position switch at 40,40,50. I change it to 40,40,-40. Usually I use gear channel and not the gyro screen. Now only if the weather would clear up

PM  EMAIL  GALLERY  Attn:RR  Quote
01-23-2018 12:57 PM  27 days agoPost 5
ICUR1-2

rrElite Veteran

Ottawa, Ontario

My Posts: All  Forum  Topic

I hear ya, I have the itch.

45% in the radio may not be 45% in the unit. Use the software to check the variance between the unit and radio.

spending time, paying attention

PM  EMAIL  GALLERY  Attn:RR  Quote
01-24-2018 02:27 AM  26 days agoPost 6
pctomlin

rrVeteran

Texas

My Posts: All  Forum  Topic

Positive numbers are HH and the inverse is the same value in rate mode.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-26-2018 10:20 AM  24 days agoPost 7
rik

rrNovice

Italy

My Posts: All  Forum  Topic

ICUR1-2
45% in the radio may not be 45% in the unit. Use the software to check the variance between the unit and radio.
You can have the same value in the transmitter and Brain by correcting the endpoints/ATV of the transmitter as you should in panel 5 of the wizard for all channels. Not only for aileron, elevator, throttle, tail, but also for tail gain and aux channels.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-26-2018 12:48 PM  24 days agoPost 8
nappyroots2182

rrElite Veteran

Moline, il

My Posts: All  Forum  Topic

Thanks rik,I just checked and changed that. Also found that my flight mode agilitys were not in my stunt mode switch. I guess that's what I get for copying from sd card that someone else gave me. Lol. It was flying really well last nite

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 173 views POST REPLY
HelicopterFlybarless Rotor Head SystemsBrain iKon › Non heading hold
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Monday, February 19 - 2:19 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online