RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 397 views
Scorpion Power Scorpion Power
07-11-2017 06:56 AM  4 months agoPost 1
bohelinut

rrNovice

Hartselle,AL

My Posts: All  Forum  Topic

wanted to see if anyone is experience this, my problem is in the tail rotor gain, since I have a separate gain channel on my TX, the gain slider in the demon software does not work,I adjust the gain in the gyro sensitivity in the TX, now at this point, if I set a high gain like 80 the servo travel is reduced, and the speed is slower, if I reduce my gain (on the HH side) to 50 the servo atv is as it should and the speed is there, however there is little gyro gain???? Whats happening????? Ive tried different digital tail servos, since I'm running 6v, I bought a Savox 1290 mg tail servo haven't tried to hover it yet

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-11-2017 08:39 AM  4 months agoPost 2
CoachE

rrApprentice

Cincinnati, ohio​-usa

My Posts: All  Forum  Topic

hmmm sounds like there is a weird mix activated. what radio, receiver and sats are you using?

Team JR / Get !T - Got !T - Perfect !T

PM  EMAIL  GALLERY  BLOGAttn:RR  Quote
07-12-2017 07:12 AM  4 months agoPost 3
bohelinut

rrNovice

Hartselle,AL

My Posts: All  Forum  Topic

BDemon

I'm using Jr 9503, 921 rec(DSM) one sat, I'm using the wire loom in the demon, the head gyro works fine, its great, but I cant get the tail dialed in , it feels week, like low gyro gain?????

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-12-2017 08:41 AM  4 months agoPost 4
CoachE

rrApprentice

Cincinnati, ohio​-usa

My Posts: All  Forum  Topic

Based on the equipment you described. You should be able to connect and fully control all 6 channels on the Bavarian Demon. I would go back to the #2 tab "diagnose" and get all the control surfaces/channels to work in perfect sync. Radio-reciever-FBL. If all of that checks out. Then you have a mechanical issue to uncover. Good luck! Keep us posted.

Team JR / Get !T - Got !T - Perfect !T

PM  EMAIL  GALLERY  BLOGAttn:RR  Quote
07-13-2017 01:58 AM  4 months agoPost 5
bohelinut

rrNovice

Hartselle,AL

My Posts: All  Forum  Topic

Bavarian Demon 3x

Well guys this afternoon I got a chance to hover the 145 again and see how the tail was, later I discovered I was using a 4.8v JR tail servo but running a 6vole pack, and I was paying attention to the travel and the speed of the tail rotor servo, long as they are reacting and correcting in the correct input don't pay attention the the speed or travel of the servo, just let the demon do its demon thing, thanks for your replies and I want to special thank Danny for his patience,support of all the phone calls,texts, emails, thanks Danny, now I need to fly her upstairs and tweak the demon and Ill be set.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 397 views
Scorpion Power Scorpion Power
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Saturday, November 18 - 6:40 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online