RunRyder RC
 3  Topic Subscribe
WATCH
 1 page 452 views POST REPLY
HelicopterFlybarless Rotor Head SystemsSpartan Vortex › Spartan VX1 and Raptor 50
04-26-2017 04:48 AM  13 months agoPost 1
Toad95

rrNovice

Jacksonville, IL

My Posts: All  Forum  Topic

I have a Raptor 50 with an unknown FBL head on it, no control unit (bought it at a swap meet). I picked up a NIB Spartan VX1 in Toledo. Bought a new Data Pod. Updated Data Pod and VX1 to latest firmware. Watched a lot of Bert's videos on you tube (a lot of good information). I am using JR DS8231 digital servos on pitch, aileron and elevator (all test good and normal on a regular receiver). The ail. and elev. servos wont center very quickly when plugged into the Vortex, the pitch servo works normally. I have set the the setting to "digital" in the Swash section in the VX1. I don't believe it to be a servo problem as much as a setting problem that I have missed. If anyone has any suggestions or solutions please LMK. This is my first attempt at FBL.

Thanks, John

PM  EMAIL  GALLERY  Attn:RR  Quote
04-26-2017 11:36 AM  13 months agoPost 2
Warbird 72

rrNovice

Boonsboro

My Posts: All  Forum  Topic

Raptor 50
I have 5 raptor 50 helicopters. All flybar tho. Thinking about changing one to flybarless. LMK as well the best set up beastx. Thanks all.

PM  EMAIL  Attn:RR  Quote
04-26-2017 03:53 PM  13 months agoPost 3
don s

rrElite Veteran

Chesapeake, VA

My Posts: All  Forum  Topic

I don't have your brand, but on my ships the cyclic servos return to center gradually while on the bench.

E820, Raptor G4N, X50F/E, E620, Forza 450, and some planks.

PM  EMAIL  GALLERY  Attn:RR  Quote
04-26-2017 07:41 PM  13 months agoPost 4
ticedoff8

rrKey Veteran

Morgan Hill, CA. USA

My Posts: All  Forum  Topic

What he said ^^

Really, it comes down to two things:
1) Does the swash maintain a more-or-less horizontal orientation as you rock and roll the heli's body left, right, nose up and nose down?
This is "compensation".
If you tilt the nose down and the swash tilts forward, you have the compensation reversed.
It is similar to a tail rotor gyro. You expect would the swash to tilt back when the nose goes down

2) Does the swash follow the sticks as you would normally expect (both collective and cyclic)?
The slow return to horizontal after a cyclic input is normal.
But, the collective should follow the stick as fast as you can move the collective stick. There should be no delay and no log with collective.

Believe 1/2 of what you see and none of what you hear.
Fake News will be the downfall of our Republic!

PM  EMAIL  GALLERY  Attn:RR  Quote
04-28-2017 03:44 AM  13 months agoPost 5
Toad95

rrNovice

Jacksonville, IL

My Posts: All  Forum  Topic

Thanks for the help
Ok Guys, according to the information you gave me I have everything correct. I was concerned about the slow return to center on the ail. and elev. servos but you say its normal. Ticedoff, the swash responds as you say it should by staying relatively level as the helicopter is rocked forward, backward and side to side. I think I have it. Thanks again for your help.

John

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 452 views POST REPLY
HelicopterFlybarless Rotor Head SystemsSpartan Vortex › Spartan VX1 and Raptor 50
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Thursday, May 24 - 10:45 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online