RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 288 views POST REPLY
Scorpion Power Scorpion Power
Helicopter
e-
Blade
Blade 300 › Question(s) about step g for the beast controller on a 300 CFX
04-17-2017 02:06 AM  6 months agoPost 1
totally_awesome

rrApprentice

Fredericksburg, Virginia

My Posts: All  Forum  Topic

Hello,

I have several questions about step g, which is servo centering. Step G allows the user to see the limits of travel for each servo, so the user has to "eyeball" the middle/center for each individual servo?
So what happens if the center is found for each servo and the swashplate plate is not level? Do you have to take the horn off the servo(s) and readjust them until the swash is level?
The three arms from the servo to the swash have been measured and are almost identical, 2 digits to the right of the decimal point measured with a micrometer.
When I try to adjust the pitch to +12 and -12 I am not at 0 degrees pitch, the video I a watching says to repeat step g if you are not at 0 degrees pitch

Regards, Dave

PM  EMAIL  Attn:RR  Quote
04-17-2017 08:05 AM  6 months agoPost 2
Heli Fanatix

rrVeteran

Fountain Valley, CA

My Posts: All  Forum  Topic

PM  EMAIL  GALLERY  Attn:RR  Quote
04-17-2017 11:01 PM  6 months agoPost 3
totally_awesome

rrApprentice

Fredericksburg, Virginia

My Posts: All  Forum  Topic

Thank you for the video!

Hello,

Thank you for the video! This is the best video I have seen on this subject!

Regards, Dave

PM  EMAIL  Attn:RR  Quote
04-17-2017 11:41 PM  6 months agoPost 4
totally_awesome

rrApprentice

Fredericksburg, Virginia

My Posts: All  Forum  Topic

Hello,

I have a level swash, but I do not have 0 pitch at mid stick with a linear pitch curve. So I will have to adjust the arms from to swash plate to the grips to get 0 degree pitch.
So I have questions about the blade grips. Are blade grips interchangable? Is there a "top" of a blade grip?

Regards, Dave

PM  EMAIL  Attn:RR  Quote
04-18-2017 01:35 AM  6 months agoPost 5
PilotPin

rrApprentice

Indiana -- USA

My Posts: All  Forum  Topic

The blade grips are interchangeable. I think there is a top and bottom . Look at where the blade bolts go through the grip . If one side has a recess with hex sided that's the bottom where the nut goes.

PM  EMAIL  GALLERY  Attn:RR  Quote
04-18-2017 07:45 AM  6 months agoPost 6
Heli Fanatix

rrVeteran

Fountain Valley, CA

My Posts: All  Forum  Topic

The 300CFX ultilizes trailing edge ... meaning
- swashplate goes down = positive collective
- swashplate goss up = negative collective

Red arrow indicates the trailing edge of blades
Green arrow indicates the blade grip

As you can see, the blade grips can be flipped but than it's not the stock configuration of the 300CFX

- Scott

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 288 views POST REPLY
Scorpion Power Scorpion Power
Helicopter
e-
Blade
Blade 300 › Question(s) about step g for the beast controller on a 300 CFX
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Sunday, October 22 - 12:44 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online