RunRyder RC
 2  Topic Subscribe
WATCH  1 page 143 views POST REPLY
Hitec RCD ProModeler
Home > Radio - Mikado VBAR Control System > VBar setup on a JR11x
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

This is my 1st time setting up my heels as I had a friend do it for me. But know he is off doing drone racing.

I just built a new Senergy N5c.

Silverline VBar w/ 2 DSMX satellites
OS55HZ w/ OS Powerboost pipe and Align Gov sensor
SwitchGlo Pro
Torq 9180 on cyclic
Torq 9180 tail servo
BK 5001HV on throttle
TP 2S 2800mAh lipo
Rail 606 main blades and V-Blade 95mm tail blades

I have the Silverline setup mostly. I am not sure on how to do exactly setup the channels for the Switchglo, how to set up the idle up switch, throttle hold, etc.

I have the throttle, collective, tail and swash all working correctly.

I plugged the SwitchGlo into the RUDD/AUX port. But when I am moving the cyclic stick on Tx to the right it turns on the SwitchGlo. When I turn it to the left it turns off.

I know that the channels on the 11x have been reassigned for my DJI F550 hexa. I am not sure if that is a problem. Can the channels be assigned differently in each model?

Any help would be greatly appreciated! Thanks in advance, Eugene

Just call me Farmer Brown. 'Cause I know how to really plant 'em

01-26-2017 02:40 AM
PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
Dan Minick

Key Veteran

Columbus, WI

My Posts: All  Forum  Topic

One of the first steps in the V vbar software is to setup your channels/ directions. Once you have completed the V bar setup wizard all that is left to do for setting your head speeds on an idle switch is through the radio software. Same with the hold, its all in your radio.
All you are doing for throttle in Vbar is setting the MIN/ MAX travel and if using the gov the MAX speed allowed by the Vbar gov. Along with your gearing info.

For the switch glow ,go into the Receiver setup tab and assign Aux 2 to the desired radio channel number. Then plug the Switchglo into the Rudder/AUX 2 port and set up the switch to control that channel. I do NOT recommend keeping it on a channel with something else like the tail in your instance.

You are not changing the actual channel on the radio when doing this, the radio always stays the same. However, you are assigning channels to switches. That is done for each model as you like.

Team Synergy, Team FBL Rotors---Formerly Dyecocker1-------if its not broke...it will be!

02-02-2017 01:00 PM
PM  EMAIL  GALLERY  Attn:RR
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

Thanks I will give it a try. I have tried to get help locally but no 1 seems to know or can help. So now I have a shelf queen until I can get the Tx set up.

Thanks again for your help, Eugene

Just call me Farmer Brown. 'Cause I know how to really plant 'em

02-02-2017 01:37 PM
PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
Dan Minick

Key Veteran

Columbus, WI

My Posts: All  Forum  Topic

Have you been able to resolve this?

Team Synergy, Team FBL Rotors---Formerly Dyecocker1-------if its not broke...it will be!

02-10-2017 12:45 AM
PM  EMAIL  GALLERY  Attn:RR
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

Haven't had time to play with it. Hopefully this weekend I can. I sure appreciate your helping!

Just call me Farmer Brown. 'Cause I know how to really plant 'em

02-10-2017 01:36 AM
PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
WATCH  1 page 143 views POST REPLY
Scorpion Power Hitec RCD
Home > Radio - Mikado VBAR Control System > VBar setup on a JR11x
 Print TOPIC Advertisers 

 2  Topic Subscribe

Thursday, March 23 - 9:19 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies