RunRyder RC
 14  Topic Subscribe
WATCH
 4 pages [ <<    <    ( 1 )     2      3     NEXT    >> ] 3100 views POST REPLY
GLOBAL 3D ProModeler
HelicopterScale Model RC Helicopters Docs  Another AS 350 Build...
01-24-2017 10:49 PM  5 months agoPost 1
doorman

rrProfessor

Sherwood, Arkansas

My Posts: All  Forum  Topic

Brooklyn Jim had to post this for sale and I finally couldn't resist any longer, so I grabbed it up...
I will say this for the kit/mechanics... they are definitely not the "norn" we/I am used to... downloaded the manual and went at it.. started Saturday for awhile and then yesterday... in setting up the BD 3x I found that I needed to change some of the dimensions given in the manual to make things come in properly...nothing bad or hard, but it made me think!!!
Overall, I am quite pleased with this model and hope to get some test hovering in by the end of the week....

Stan

AMA 2918-Team JR, Spin Blades, East Coast Scale Helicopter,Castle Creations

PM  EMAIL  GALLERY  Attn:RR
01-24-2017 11:10 PM  5 months agoPost 2
TailKiller

Senior Heliman

Panama City, FL

My Posts: All  Forum  Topic

Will be following...

,Dennis
http://pcrcheliclub.com/
700 Astar Super Scale T-600 Bell 206 Trex 600 Naza H DX8

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-25-2017 12:44 AM  5 months agoPost 3
doorman

rrProfessor

Sherwood, Arkansas

My Posts: All  Forum  Topic

Read Yours!!

tailkiller,
I went through your thread and tintmaster too!!
So far my first spool up today on the table didn't show any signs of a shake...I did change out the main shaft bearings and the tail drive shaft ones, before I even started the assembly.., the ones in it were a vrry poor quality, with almost a 1/16" movement at the top of the main shaft!!
It is smooth on the table when spinning by hand, but it makes a lot more noise then I expected... head feels good, and haven't gotten to checking the blades yet..
Will let you know how it goes later in the week.,,
Stan

AMA 2918-Team JR, Spin Blades, East Coast Scale Helicopter,Castle Creations

PM  EMAIL  GALLERY  Attn:RR
01-25-2017 01:44 AM  5 months agoPost 4
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

Welcome to the insanity Stan!!!!

Someday i would like to get in on a scale funnily with you guys!!

Keep up the good work, Eugene

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-25-2017 01:46 AM  5 months agoPost 5
TailKiller

Senior Heliman

Panama City, FL

My Posts: All  Forum  Topic

There is a lot of trial and error in my post. Bearing are a good move.

,Dennis
http://pcrcheliclub.com/
700 Astar Super Scale T-600 Bell 206 Trex 600 Naza H DX8

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-25-2017 02:01 AM  5 months agoPost 6
neverhappy

Senior Heliman

Piedmont.Al. USA

My Posts: All  Forum  Topic

New project

I'm subscribed. Stan love the no new project talk we had while I was there in December!! I think we both knew in the back of our heads that wouldn't happen!!!

Looking good my friend

Jeffrey:) (Love and Peace to all)

PM  EMAIL  GALLERY  Attn:RR
01-25-2017 03:12 AM  5 months agoPost 7
Mojave

Elite Veteran

Palos Verdes, Ca. USA

My Posts: All  Forum  Topic

That's one good looking AS350 bud! I'm sure you'll work your way through the bugs in the build. Those mechs are noisy, but they are reliable.
Barry

All helis and planes have an expiration date stamped on them...you only find it after you crash!!

PM  EMAIL  GALLERY  Attn:RR
01-25-2017 03:26 AM  5 months agoPost 8
BrooklynJim

Heliman

Starlight, PA

My Posts: All  Forum  Topic

Stan..
you really jumped on this one.. my UPS return receipt hasnt even come back to me yet!! lol..

dont forget the vids, i looked thru the kit as i was packing it up and as you mentioned ( PM ) the mechanics are a one off, but hey.. if it works, who am i to criticize but based on what i too have ready, good move on the bearings..

im subscribed!!

and thanks for the feedback brother..

PM  EMAIL  GALLERY  Attn:RR
01-25-2017 02:06 PM  5 months agoPost 9
Copter Doctor

rrProfessor

Enterprise/ft.rucker ,al- home of army aviation

My Posts: All  Forum  Topic

A while back a bunch of us were building bell 407's, looks like now we are having an A-Star party. my A-Star posts have been pretty quiet n slow but I may get it going again.
Stan my friend, I have no doubt that A-Star will be a masterpiece (it looks really nice already) when you are thru with it.

drive a rotary, fly a rotorcraft

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-25-2017 10:44 PM  5 months agoPost 10
doorman

rrProfessor

Sherwood, Arkansas

My Posts: All  Forum  Topic

Votes Of Confidence!!!

Thanks everyone for the support!!!!
Well, I got a little further today..
Got the tail boom mounted.. that was interesting.. felt like a one armed paper hanger!!!
Everything is mounted and the loctite is curing along with some glue and stuff!!!
I also included a picture with some very specialized heli tools that you absolutely need to build scale!!
Weighed each blade and they were all dead nuts at 136.2, so I am please with that.. setting up the ESC it seems it likes a 1350 hs... I have read some are running in the 1400's, so time will tell...
I did spool it up in the shop (no blades :eek and all seems to run smooth so far... if the wind lays down a bit tomorrow, I may just need to test pop her...it is going to need nose weight... haven't got to that yet, but first job in the morning.....
Will let you know how it goes!!!

AMA 2918-Team JR, Spin Blades, East Coast Scale Helicopter,Castle Creations

PM  EMAIL  GALLERY  Attn:RR
01-25-2017 11:01 PM  5 months agoPost 11
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

Looking good!!!

Question: what do you guys use to paint the blades with?

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-25-2017 11:08 PM  5 months agoPost 12
TailKiller

Senior Heliman

Panama City, FL

My Posts: All  Forum  Topic

Looking good. It will take a lot of nose weight. You can hot glue lead shot in the instrument panel.

,Dennis
http://pcrcheliclub.com/
700 Astar Super Scale T-600 Bell 206 Trex 600 Naza H DX8

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-26-2017 12:04 AM  5 months agoPost 13
Grimracer

Veteran

Eau Claire WI

My Posts: All  Forum  Topic

likey likey... thanks for sharing Champ

Michael J Zaborowski

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-26-2017 01:00 AM  5 months agoPost 14
doorman

rrProfessor

Sherwood, Arkansas

My Posts: All  Forum  Topic

Thanks!!

Yep, it is going to need quite a bit to get this guy balance... but I have plenty of lead and stuff I can stick to it... tools and rocks and maybe the cat
These blades came painted as you see them, but when I do paint them I use automotive Duplicolor.. spray bombs, but the tip gives an excellent pattern, and the paint dries quickly.. just shoot light even coats to keep the weights as close as possible... I spray the bottoms flat black... if you need to add weight to a blade, just shoot more flat black on the bottom..
Now to come up with some nice graphics!!!
Stan

AMA 2918-Team JR, Spin Blades, East Coast Scale Helicopter,Castle Creations

PM  EMAIL  GALLERY  Attn:RR
01-27-2017 02:17 PM  5 months agoPost 15
doorman

rrProfessor

Sherwood, Arkansas

My Posts: All  Forum  Topic

Progress..

Got the lead shot and epoxy added yesterday to get the C/G correct.. wired up the new 6s batt's, still need to add the airborne battery.. final check the BD 3X and wait for the "breeze" to slow down a bit for the test hops..
Then I can move onto the added little touches...

Stan

Stock blades thoughts from any that have used them... the cord looks a bit narrow to me, but I am used to Spin Blades and wide cords!!! (????)

AMA 2918-Team JR, Spin Blades, East Coast Scale Helicopter,Castle Creations

PM  EMAIL  GALLERY  Attn:RR
01-27-2017 03:46 PM  5 months agoPost 16
neverhappy

Senior Heliman

Piedmont.Al. USA

My Posts: All  Forum  Topic

Build

Get r done!

Where's the video??

Jeffrey:) (Love and Peace to all)

PM  EMAIL  GALLERY  Attn:RR
01-27-2017 05:06 PM  5 months agoPost 17
doorman

rrProfessor

Sherwood, Arkansas

My Posts: All  Forum  Topic

Video?

Not much luck with video.. have trouble sharing it, and getting someone to shoot it when I fly... guess you will have to take mu word on it!!!

AMA 2918-Team JR, Spin Blades, East Coast Scale Helicopter,Castle Creations

PM  EMAIL  GALLERY  Attn:RR
01-27-2017 05:44 PM  5 months agoPost 18
TailKiller

Senior Heliman

Panama City, FL

My Posts: All  Forum  Topic

Hope that your test hops are all good.

,Dennis
http://pcrcheliclub.com/
700 Astar Super Scale T-600 Bell 206 Trex 600 Naza H DX8

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-27-2017 07:18 PM  5 months agoPost 19
Copter Doctor

rrProfessor

Enterprise/ft.rucker ,al- home of army aviation

My Posts: All  Forum  Topic

Stan, when I first got mine I hovered the stock blades for a couple mins n I concluded that I could see why a stab unit is recommended with these kits. But I've seen them perform seemingly flawlessly with a proper unit, remember Donnie's 412 at top gun? Quality wise they look fine. I used heavier blades with no stabilization but u know me ;-)

drive a rotary, fly a rotorcraft

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-27-2017 08:23 PM  5 months agoPost 20
doorman

rrProfessor

Sherwood, Arkansas

My Posts: All  Forum  Topic

INFO...

Thanks Emile...

I will give these a try once the wind lays down... beautiful day out, it's just hard to stand up or the testing would have begun!!!
Those that know me, know the wind has to be going pretty good to slow me down..
Emile, I am running the PNP head with the stock blades and a BD 3X so I will give them a try...I do remember seeing Donnie's fly and I know that Joel's machines all look smooth as silk!! (I think Joel could make a brick fly smoooooothly though!!! )

Thanks, Stan

AMA 2918-Team JR, Spin Blades, East Coast Scale Helicopter,Castle Creations

PM  EMAIL  GALLERY  Attn:RR
WATCH
 4 pages [ <<    <    ( 1 )     2      3     NEXT    >> ] 3100 views POST REPLY
Scorpion Power GLOBAL 3D
HelicopterScale Model RC Helicopters Docs  Another AS 350 Build...
 Print TOPIC  Make Suggestion 

 14  Topic Subscribe

Thursday, June 29 - 3:06 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online