RunRyder RC
 9  Topic Subscribe
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 985 views
Scorpion Power Scorpion Power
Helicopter
e-
Castle Electric Components
› Low head speed problem
10-07-2016 03:07 PM  13 months agoPost 21
don s

rrElite Veteran

Chesapeake, VA

My Posts: All  Forum  Topic

Probably time to start swapping out components...

E820, Raptor G4N, X50F/E, E620, Forza 450, and some planks.

PM  EMAIL  GALLERY  Attn:RR  Quote
10-07-2016 03:34 PM  13 months agoPost 22
mtickel25

rrNovice

columbia, s.c. -​u.s.a.

My Posts: All  Forum  Topic

like what?....everything is brand new and supposedly enough power for this size heli....

PM  EMAIL  GALLERY  Attn:RR  Quote
10-07-2016 06:06 PM  13 months agoPost 23
JuanRodriguez

rrProfessor

The Villages,​Florida

My Posts: All  Forum  Topic

I would do the entire setup over again as if it was the first time setting it up ......while paying close attention to the procedures suggested in this thread. You may have inadvertently missed something the first time around ...... since it's not working for you as is you have nothing to loose by starting from scratch......

Been there, done that and old enough to know better.....

PM  EMAIL  GALLERY  Attn:RR  Quote
10-07-2016 06:20 PM  13 months agoPost 24
plakkertje

rrApprentice

belgium

My Posts: All  Forum  Topic

I dont know if you know, but on a castle the motor speed is less than with an yge ore kontronik erc full throtle.
you can not get the same headspeed with it compared to other brand, that is the only bad thing in my opinion.
but is is so easely to set it up, jou just calibrate and put the values on the pc and go.
If the tail kiks to mutch with pitch pumps lower the gov gain, mine is at 9 for my 700 birds.

sorry for my bade writhing i am from belgium.

PM  EMAIL  Attn:RR  Quote
10-08-2016 12:38 PM  13 months agoPost 25
plakkertje

rrApprentice

belgium

My Posts: All  Forum  Topic

You can also play with the tail precomp with the pitch pumps

PM  EMAIL  Attn:RR  Quote
10-10-2016 12:38 AM  13 months agoPost 26
mtickel25

rrNovice

columbia, s.c. -​u.s.a.

My Posts: All  Forum  Topic

How do you set tail precomp? In the msh brain software?

PM  EMAIL  GALLERY  Attn:RR  Quote
10-10-2016 01:33 AM  13 months agoPost 27
Slowpoke

rrKey Veteran

Dublin, OH

My Posts: All  Forum  Topic

yes, that's in the brain software

PM  EMAIL  GALLERY  Attn:RR  Quote
12-16-2016 06:08 AM  11 months agoPost 28
plakkertje

rrApprentice

belgium

My Posts: All  Forum  Topic

Gov gain is to high at 15, try down to 8or9
tail kick will be less ore gone. (Do some precomp in the tail on fbl also)

PM  EMAIL  Attn:RR  Quote
12-16-2016 03:39 PM  11 months agoPost 29
Pistol Pete

rrProfessor

Seffner, FL

My Posts: All  Forum  Topic

A simple throtle test is to remove blades, disable SET GOV and use a linear throtle curve directly.

The ESC software will let you know which GOV (high or low) is correct.

This way you can verify that you are getting full throtle response in relation to your Tx throtle calibration to ESC.

After confirming above, adjust throtle to a flat curve that suits the head speed you're after. You could start at +35 given radio, since Zero would be 50% to ESC.

Eventually you can go back to SET GOV but the above works at the field without the need of a PC.

~~Enjoying the hobby one flight at a time~~

PM  EMAIL  HOMEPAGE  GALLERY  BLOGAttn:RR  Quote
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 985 views
Scorpion Power Scorpion Power
Helicopter
e-
Castle Electric Components
› Low head speed problem
 Print TOPIC  Make Suggestion 

 9  Topic Subscribe

Saturday, November 18 - 12:38 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online