RunRyder RC
 4  Topic Subscribe
WATCH
 1 page 1148 views POST REPLY
Scorpion Power GLOBAL 3D
Helicopter
e-
Align
T-REX 700 › Trex 700 x build pictures
08-27-2016 10:01 PM  10 months agoPost 1
Helinige

Heliman

England

My Posts: All  Forum  Topic

Currently building one, looking for a few ideas regarding servo wiring battery harness wires Etc . Post up what you have guys, be very welcome and appreciated ..

Cheers.

Regards Nigel

PM  EMAIL  GALLERY  Attn:RR
08-28-2016 12:33 AM  10 months agoPost 2
nynextel88

Senior Heliman

longisland, NY

My Posts: All  Forum  Topic

Hey there, page 11 in the manual shows good places to zip tie on the frame for your servos. I followed that and my setup came out pretty nicely.

For the ESC I have the wires come down through the opening at the very top of the electronics mount, then routed them back into the frame where motor wires are. Came out pretty clean.

Team Align (Enterprise Hobby)
Thunder Power RC

PM  EMAIL  GALLERY  Attn:RR
08-28-2016 09:00 AM  10 months agoPost 3
Helinige

Heliman

England

My Posts: All  Forum  Topic

Trex 700 x

Hi, yes seen the wording detail in manual, but not too sure as wanted to try and tuck them away, I'm going to have a look today and will post a few pics as I go through each one, I do like the esc wiring you have though.

Many thank .

Nige

Regards Nigel

PM  EMAIL  GALLERY  Attn:RR
08-30-2016 08:23 PM  10 months agoPost 4
nynextel88

Senior Heliman

longisland, NY

My Posts: All  Forum  Topic

All servo leads get tucked away real nicely inside the frame if you follow the zip tie spots. Only place you really see the wires is where they enter the frame

Team Align (Enterprise Hobby)
Thunder Power RC

PM  EMAIL  GALLERY  Attn:RR
09-03-2016 02:33 PM  9 months agoPost 5
tgalo

Senior Heliman

USA

My Posts: All  Forum  Topic

Toying around with a aluminum bottom plate for the 700X. With some modification's to a stock Align plate, it worked out well. But not necessary I know.

Gravity's a bitch ant it?

PM  EMAIL  GALLERY  Attn:RR
09-16-2016 03:10 PM  9 months agoPost 6
mr dan

Veteran

Stockton Calif

My Posts: All  Forum  Topic

I won this kit at a recent funfly down in San Diego Calif last weekend. You mentioned wire routing. I sugest once you have the frame halves assembled that is the best time to place the servos and route the wires. They should end up like whats in the photo. The pic in the manual shows each frame half so don't get confused thinking the wires route outside the frame.

"R.I.P Roman" Citizen 0094 in the Nation

PM  EMAIL  GALLERY  Attn:RR
03-27-2017 06:40 AM  3 months agoPost 7
iyoy

Veteran

Bacolod City, Philippines

My Posts: All  Forum  Topic

Routing around pinion and main gear

Be careful with this area because there is a tendency to get the servo wires too close to the main gear and pinion. There are a lot of tutorial videos on YouTube so you might want to view those too.

iyoy

PM  EMAIL  GALLERY  Attn:RR
WATCH
 1 page 1148 views POST REPLY
ProModeler Scorpion Power
Helicopter
e-
Align
T-REX 700 › Trex 700 x build pictures
 Print TOPIC  Make Suggestion 

 4  Topic Subscribe

Wednesday, June 28 - 1:21 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online