RunRyder RC
 5  Topic Subscribe
WATCH
 3 pages [ <<    <     1      2     ( 3 )    >    >> ] 1680 views POST REPLY
ProModeler Scorpion Power
HelicopterFlybarless Rotor Head SystemsV-Bar › Silverline binding problem
01-22-2017 01:22 AM  5 months agoPost 41
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

Working on setting up the VBar. I am not sure of a couple of things.

I have upgraded to Pro so I can run the Governor in the VBar. I got an Align sensor and switched the red and black wires around.

I don't have any output to my throttle servo. Do I plug it about the Gov sensor or channel 4? Or am I missing a step?

I also am not getting any movement on swash when I move the throttle stick on the Tx (Collective I am assuming). Still learning what each movement is...

Also what channel can I use for the SwitchGlo?

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 04:36 AM  5 months agoPost 42
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

I have gotten to the "Collective" part, but I get no movement what so ever. The cyclic and tail seem to be done.

Also I am not sure how to get the throttle servo end points set. It doesn't move at all either. I have it set for the Servo No BEC port above the Gov Sensor.

Heres what I have so far:

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 01:19 PM  5 months agoPost 43
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

You have to start a new setup

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR
01-22-2017 04:00 PM  5 months agoPost 44
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

I created a new setup. Rebound it and started going through the setup. And just like before when I get to the Collective section, I have no movement.

Now I am pretty much a newly to programming. I have done nothing to the Tx except bind it. I am not sure if I am supposed to go in there and set something.

Please excuse my ignorance here.

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 04:30 PM  5 months agoPost 45
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

Just figured it out. I had set my Tx on Acro. Its an 11x. I reset it on Heli and 1 servo. I guess its not like on my older 9303 where you use Acro.

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 04:52 PM  5 months agoPost 46
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

Now I am only getting half throttle on the throttle servo. I am at the last GovII section and trying to set the endpoints. But it only goes half way no matter what I do.

Or do I set the endpoints in another place?

With no power, I can get full travel on the throttle servo from close to open.

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 08:15 PM  5 months agoPost 47
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

Could it be the frequency not set right? I don't know where to find that on the throttle servo. Or settings for it. Any ideas?

I can plug 1 of my Torq cyclic servos into the Servo no BEC and get full travel with it.

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 08:37 PM  5 months agoPost 48
jjeaster222000

Veteran

Bedford in

My Posts: All  Forum  Topic

do you have just a regular receiver where you can try the servo? just to make sure it is bad?

Team Synergy

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 08:43 PM  5 months agoPost 49
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

It is a tail servo. Just tried it in the tail servo and it works. So I don't think I can use it for throttle.

Can I use a BK mini cyclic servo DS-5001HV? I want to have all HV servos.

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 09:20 PM  5 months agoPost 50
jjeaster222000

Veteran

Bedford in

My Posts: All  Forum  Topic

What servo was it? I've used a futaba before. I forget the number but I used the mini tail servo from futaba on the throttle.

Team Synergy

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 09:38 PM  5 months agoPost 51
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

It is a BK DS-7005HV

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-22-2017 11:10 PM  5 months agoPost 52
tintmaster

Key Veteran

Wichita, Ks. U.S.A.

My Posts: All  Forum  Topic

I just ordered a new BK DS-5001HV cyclic servo.Will be here Wednesday. Then I shall try it again!!

Just call me Farmer Brown. 'Cause I know how to really plant 'em

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
WATCH
 3 pages [ <<    <     1      2     ( 3 )    >    >> ] 1680 views POST REPLY
GLOBAL 3D ProModeler
HelicopterFlybarless Rotor Head SystemsV-Bar › Silverline binding problem
 Print TOPIC  Make Suggestion 

 5  Topic Subscribe

Tuesday, June 27 - 4:45 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online