RunRyder RC
 5  Topic Subscribe
WATCH
 1 page 716 views POST REPLY
HelicopterRadio - Servo - Gyro - Gov - Batt › Original throttle jockey pro
06-17-2015 05:38 PM  35 months agoPost 1
Jamovich

rrVeteran

Bangalore, India

My Posts: All  Forum  Topic

hi guys

I got a the first version of the throttle jockey pro and I wish to reconfigure it for a new setup. Problem is I cannot seem to enter calibration mode when I flick the aux (flight phase) switch on/off/on during the first 3 seconds when the RX is turned on as according to the instructions. ATV on the aux channel is 100/100 and 110/110 on the throttle end points. I'm using a t-14mz with 2.4ghz

Thanks for any inputs

PM  EMAIL  GALLERY  Attn:RR  Quote
06-25-2015 10:59 AM  35 months agoPost 2
Richardmid1

rrProfessor

Leeds, England

My Posts: All  Forum  Topic

Ridiculously complicated to setup! Anyway, are there any lights that change when you flick the AUX channel switch? Is the AUX channel switch assigned to the AUX channel? Have you tried 0/100 or 100/0 in the AUX channel travel adjust?

60% of the time, it works every time!

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-25-2015 11:49 AM  35 months agoPost 3
ICUR1-2

rrElite Veteran

Ottawa, Ontario

My Posts: All  Forum  Topic

try reversing the aux channel

PM  EMAIL  GALLERY  Attn:RR  Quote
10-30-2015 09:47 PM  31 months agoPost 4
allns47

rrKey Veteran

Richmond IN.

My Posts: All  Forum  Topic

I ran into this also,,,,when calibrating,,,,the channel u have the gain on you must set it to -100 and +100.....Once calabration is complete,,,go back to whatever channel u have gain plugged in and set the gain values to the head speed you want,,,If you have a 2 position switch you would set one point to 0 which will turn tjpro off antd the other position to whatever headspeed you want,,,,,if you have a 3 position switch during calabration you need to do set it as -100 0 +100,,,after calabration you need to set the switch to 0 and then the other 2 positions you can have to different head speeds..

PM  EMAIL  GALLERY  Attn:RR  Quote
10-31-2015 02:22 AM  31 months agoPost 5
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

Ridiculously complicated to setup!
You mean turn on power, flip a switch back and forth a couple of times, full throttle, low throttle, flip the switch again and you're done is ridiculously complicated?

You usually will have a problem if you use a channel with a three position switch to get it into cal mode.

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
11-02-2015 12:47 PM  31 months agoPost 6
allns47

rrKey Veteran

Richmond IN.

My Posts: All  Forum  Topic

no problem using a 3 postion switch,,during calabration just make sure u set the switch values at -100,,,0,,,,+100,,never adjust the atvs...leave the -100 +100,,,after you calabrate set the switch to 0...the next two values whatever u want the head speed,,,example 0....64...72

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 716 views POST REPLY
HelicopterRadio - Servo - Gyro - Gov - Batt › Original throttle jockey pro
 Print TOPIC  Make Suggestion 

 5  Topic Subscribe

Friday, May 25 - 10:17 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online