RunRyder RC
 0  Topic Subscribe
WATCH
 1 page 771 views POST REPLY
Scorpion Power Scorpion Power
HelicopterRadio - Servo - Gyro - Gov - Batt › TJ PRO Pics anyone?
12-21-2003 11:23 AM  13 years agoPost 1
scouse

rrApprentice

UK Liverpool

My Posts: All  Forum  Topic

Just got myself a TJ Pro
Anyone got any pics on mounting the sensor onto a TT50? and is it OK to just use the original holes in the TT fan(just couldn't be bothered measuring and drilling new holes )


Thx

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
12-21-2003 12:42 PM  13 years agoPost 2
blakka_1

rrElite Veteran

London/Enfield

My Posts: All  Forum  Topic

i dont have any pics but, yes it is fine 2 use the standard holes already drilled into the tt fan, ive dun so on my heli with tt50 and tj pro and the magnets fit in perfectly (just make sur you glu them in).

PM  EMAIL  Attn:RR  Quote
12-21-2003 01:53 PM  13 years agoPost 3
Al Magaloff

rrMaster

12,199 Posts- Enough Time Wasted. See Ya!

My Posts: All  Forum  Topic

Mount the sensor on the supplied bracket to the motor mount bolts. The instructions are pretty explanatory. The brackets have an off set . Make sure to off set in the correct direction, so the sensor is under the magnet.

PM  EMAIL  Attn:RR  Quote
12-21-2003 02:09 PM  13 years agoPost 4
capebob

rrVeteran

Cape Coral, FL

My Posts: All  Forum  Topic

Here's a picture for what it's worth. Fairly straight forward installation.

Bob

Success is the ability to go from one failure to another with no loss of enthusiasm. Churchill

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
12-21-2003 03:47 PM  13 years agoPost 5
scouse

rrApprentice

UK Liverpool

My Posts: All  Forum  Topic

Cheers fellas
The instructions do look easy like, but the main reason i was asking is, that if i remember rightly, someone in an earlier post somewhere managed to set the bracket up wrong and smashed their sensor to bits . So thought i'd check out someone elses setup first.
Dont want to be waiting for anything in the mail at this time of year

Thanks again

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
12-26-2003 09:02 PM  13 years agoPost 6
SLiebl

rrApprentice

Lancaster, PA - USA

My Posts: All  Forum  Topic

You might also have to put a tiny hole in the pocket where the magnet goes. When I epoxied the magnets into the fan, the epoxy creates an air tight seal and the magnets tried to push themselves out from the pressure. I used an Exacto knife to put a small slit in the plastic fan housing inside the magnet pocket.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
12-26-2003 09:11 PM  13 years agoPost 7
HelicopterJohn

rrKey Veteran

Seffner, Florida (Just East of Tampa, Florida)

My Posts: All  Forum  Topic

Small hole

SLiebl


Like you idea of making a very small hole for excess air and epoxy to escape. Will use it in the future.

I knew a great idea would come from someone in Lancaster Pa. (my birthplace).

Thanks!!!!!!!!!!!!!!!!

OC Bob's Gathering #2 was a Premiere Event. Pictures in my Gallery

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 771 views POST REPLY
Scorpion Power Scorpion Power
HelicopterRadio - Servo - Gyro - Gov - Batt › TJ PRO Pics anyone?
 Print TOPIC  Make Suggestion 

 0  Topic Subscribe

Thursday, October 19 - 1:35 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online