RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 915 views POST REPLY
Scorpion Power ProModeler
HelicopterBergen R/C Helicopters › is this correct order for gas Intrepid bearings?
12-15-2003 03:07 PM  13 years agoPost 1
HM16 Seahawk

rrApprentice

Fenton, Michigan - USA

My Posts: All  Forum  Topic

Can anyone that has built an Intrepid Gasser tell me if this is the correct order of assembly?
Thanks

PM  EMAIL  Attn:RR
12-16-2003 04:04 AM  13 years agoPost 2
Malorie

rrElite Veteran

Paw squared, MI

My Posts: All  Forum  Topic

YUP

Life's a journey, NOT a destination.

PM  EMAIL  GALLERY  Attn:RR
12-16-2003 01:02 PM  13 years agoPost 3
gyan

rrKey Veteran

Surrey, BC Canada or Blaine Wa.

My Posts: All  Forum  Topic

Just make sure the smaller ID washer for the bearing is on the outboard side. I think the tail rotor bearings are similar as well.

PM  EMAIL  GALLERY  Attn:RR
12-16-2003 02:53 PM  13 years agoPost 4
Malorie

rrElite Veteran

Paw squared, MI

My Posts: All  Forum  Topic

He has the raceless bearings, there isn't any difference in ID or OD.

Life's a journey, NOT a destination.

PM  EMAIL  GALLERY  Attn:RR
12-16-2003 11:54 PM  13 years agoPost 5
HM16 Seahawk

rrApprentice

Fenton, Michigan - USA

My Posts: All  Forum  Topic

Thanks for the help

Thanks for the help everyone. On to page 73!

PM  EMAIL  Attn:RR
12-17-2003 12:47 AM  13 years agoPost 6
gyan

rrKey Veteran

Surrey, BC Canada or Blaine Wa.

My Posts: All  Forum  Topic

That's cool thanks Malorie. But that just makes more questions!!

1 Is there any other mods being done to the Intrepid?
2 Is there a list somewhere that we can access that describes all the
mods? ...and when they were done?
3 How do we know when we order parts that we'll get the same one
we currently have?
4 How do we know if intermixed parts are ok to use?

PM  EMAIL  GALLERY  Attn:RR
12-17-2003 01:41 AM  13 years agoPost 7
Al Magaloff

rrMaster

12,199 Posts- Enough Time Wasted. See Ya!

My Posts: All  Forum  Topic

gyan, scream UPDATE THE WEBSITE as loud as you can!

PM  EMAIL  Attn:RR
12-17-2003 02:23 AM  13 years agoPost 8
Malorie

rrElite Veteran

Paw squared, MI

My Posts: All  Forum  Topic

That's in the works.

The bearings aren't any sort of a mod. They are just from a different mfg. In fact, I think we're now back to the raced bearings.

Life's a journey, NOT a destination.

PM  EMAIL  GALLERY  Attn:RR
12-17-2003 06:39 PM  13 years agoPost 9
RussR

rrApprentice

Tampa, Florida

My Posts: All  Forum  Topic

Are the bearinngs interchangeable with Min Airs? I was comparing against my Fury and they seem similar.......

PM  EMAIL  GALLERY  Attn:RR
12-18-2003 03:35 AM  13 years agoPost 10
Malorie

rrElite Veteran

Paw squared, MI

My Posts: All  Forum  Topic

Not sure if MA is using the same ID/OD beaeings or not. Most likely, if they look close, they are probably the same. Most of the mfgs are using metric bearings in similar sizes.

Life's a journey, NOT a destination.

PM  EMAIL  GALLERY  Attn:RR
12-24-2003 04:23 PM  13 years agoPost 11
RussR

rrApprentice

Tampa, Florida

My Posts: All  Forum  Topic

Thanks Mal - Since I have both birds I have been comparing certain dimensions and such, I'm finally done with the assembly on my gasser but have a few small parts on order to complete. Should be a great Xmas!

Russ

PM  EMAIL  GALLERY  Attn:RR
WATCH
 1 page 915 views POST REPLY
Scorpion Power ProModeler
HelicopterBergen R/C Helicopters › is this correct order for gas Intrepid bearings?
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Thursday, August 24 - 2:16 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online