RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 3739 views
Scorpion Power Scorpion Power
Helicopter
e-
DJI Innovations
 News  DJI PHANTOM 2 Launched!
12-16-2013 02:25 PM  3 years agoPost 1
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

PHANTOM 2 OVERVIEW:
1. PHANTOM 2 is an all in one aircraft, ready to fly without requiring configuration.
2. Built-in NAZA-M V2 flight control system with enhanced flight reliability, hover stability and easy operation.
3. Built-in DJI intelligent battery with up to 25 minutes of flight time.
4. 9 inch self-tightening propeller allow up to 1.3kg lift off weight.
5. 2.4GHz remote control system with a separate gimbal control channel.
6. Reserved gimbal port for the Zenmuse H3-2D gimbal, allows plug and play installation.
7. Pitch movement of the Zenmuse H3-2D gimbal is controllable.
8. Pre-installed powered video output cables for wireless video transmitter devices.
9. Reserved CAN-Bus extendable device connections, such as DJI iOSD mini, iOSD mark II, 2.4G Bluetooth Datalink,etc.


New Product Features:

1. Easily adjustable, ready-to-fly quad-rotor
Functions
1) Multiple control modes: GPS flight mode and ATTI. flight mode.
2) Selectable manual flight mode and Failsafe activation.
3) Intelligent orientation control (IOC), can be enabled via the PHANTOM 2 Assistant software.
4) Enhanced Failsafe mode.
5) Intelligent battery protection system.
6) PC ground station and iPAD ground station compatible (coming in January 2014).
Built-in
1) NAZA-M V2 flight control system (GPS, compass, 2.4GHz receiver).
2) Flight propulsion system.
3) Gimbal’s GCU module.
4) Micro-USB port for PHANTOM 2 assistant software configuration and online upgrade.

2. 2.4GHz Transmitter
1) Working in the 2.4GHz frequency bandwidth with a maximum communication distance of 1000m.
2) 5 proportional channels with a total of 7 channels.
3) Quick controller mode switching via PHANTOM RC Assistant Software: Mode1, Mode2.
4) Automatic return centering of both control sticks.
5) Slide lever for gimbal pitch control.

3. Intelligent battery
1) 5200mAh, ultra-large capacity for up to 25 minutes of flight time.
2) Intelligent charge and discharge protection for battery safety.
3) Battery level indicator.
4) Protective shell for battery safety.

4. Extended functions
1) Built in port for Zenmuse H3-2D gimbal allows easy plug and play functionality.
2) Pre-installed powered video output port for wireless video transmitter devices.
3) Built in extension port for iOSD mini allows easy expansion for a better flight experience.
4) Built in extension port for iOSD mark II allows a better flight experience and additional flight data recording.
5) Built in extension port for 2.4G Bluetooth Datalink for ground station capability.

Please click and watch the Phantom 2 Introduction Video

Watch at YouTube

Please click and watch the Phantom 2 How to Videos:

Watch at YouTube

Watch at YouTube

PM  EMAIL  Attn:RR  Quote
12-20-2013 11:02 AM  3 years agoPost 2
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released a new firmware V1.08 for Phantom​2!

What’s new?

Firmware
PHANTOM 2 Main Controller Firmware V1.08
1.In Phantom 2 mode, users can set a new home point manually when the aircraft is in “Ready to fly” status as long as a home point has been recorded automatically.
2.In a Failsafe situation, if less than 6 GPS satellites are found for more than 20 seconds, the aircraft will descend automatically.
3.Fixed a glitch that prevented descent after the 2nd level low battery capacity warning occurs when in Naza-m mode.

Assistant Software
1.PHANTOM 2 and PHANTOM 2 VISION will share the PHANTOM 2 Assistant Software.

User Manual
1.Added the 8-Pin port sequence on AVL58 connection diagrams.
2.Added an important note: Keep the wireless video transmission module and other communicating devices away from the compass during installation and connection to avoid interference.
3.Added a note about automatic descent when GPS satellites are found less than 6 for more than 20 seconds while in Failsafe.

Upgrade Notes
1.Upgrade the main controller and central board firmware to the latest version using Assistant Software V1.08. Be sure the central board firmware is V1.0.1.19 or above, otherwise there will be malfunction caused by version mismatch.
2.Upgrade iOSD mini, iOSD Mark II and H3-2D firmware to the latest version before using them with PHANTOM 2.
3.If you have any problems during upgrade, please contact your dealer or DJI Customer Service.

Please click here to download the V1.08 firmware.

PM  EMAIL  Attn:RR  Quote
12-31-2013 08:49 AM  3 years agoPost 3
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released assistant software for Mac!

Mac style interface
Clean, modern Mac inspired interface that Mac users will love.

Different system, same operation
Usage is the same on Mac and PC versions, so if you’re used to the PC version you can switch straight over.

No more driver installs
No more downloading drivers to install Assistant. It just works.

Watch at YouTube

Operating system: Mac OS X 10.6(Lion) or above
Supported flight systems: Phantom 2 Vision, Phantom 2, A2

Please click here to download the Mac Assistant Software for Phantom 2 Vision.

Please click here to download the Mac Assistant Software for Phantom 2.

Please click here to download the Mac Assistant Software for A2.

PM  EMAIL  Attn:RR  Quote
01-09-2014 01:40 PM  3 years agoPost 4
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released new firmware for Phantom 2​remote control!

What’s new?

Firmware

Remote Controller firmware updated to V1.0.1.11
Optimized output of the X1 channel on the Phantom 2 remote controller to improve user experience.

Important notes:

1.For the users of the PHANTOM 2 with Zenmuse H3-2D gimbal, one must adhere to the following steps to upgrade the remote controller firmware.

1)Use the PHANTOM RC Assistant software to upgrade the remote controller firmware to V1.0.1.11.
2)Calibrate the sticks and X1 channel of the remote controller using the PHANTOM RC Assistant software.
3)Use the PHANTOM 2 Assistant software to upgrade the Gimbal IMU firmware to V1.8 via upgrade page.
4)After the upgrade is completed, calibrate the X1 channel of the main controller using the PHANTOM 2 Assistant software to ensure compatibility of PHANTOM 2 and the Zenmuse H3-2D.

2.For users of PHANTOM 2 without Zenmuse H3-2D, conduct all of the above steps except the third to upgrade the remote controller firmware.

Please click here for more information.

PM  EMAIL  Attn:RR  Quote
01-13-2014 03:50 AM  3 years agoPost 5
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI is going to release an FPV Hub Kit for​Phantom 2!

PHANTOM 2 FPV HUB kit contains only cables and the FPV HUB to make connections convenient, easy and thus removing the need to do soldering when connecting them to a iOSD mini,iOSD Mark II or a DJI specified wireless video transmission module AVL58. Only 4 cables require soldering if users opt to use a wireless video transmission that’s not specified by DJI.

Connections
Choose devices collocation used with FPV-HUB according to required functions.

For wireless video transmission, the ALV58 is recommended for easy connection, using a HUB-AVL58 cable.

Collocation 1: Wireless video transmission module connected

1)Stop the Micro switch at VID position if only wireless video transmission module is connected to the FPV HUB.
2)Wireless video transmission module is an alternative to AVL58 or others unspecified. If using the AVL58, connect it to the FPV HUB via HUB-AVL58 cable. If using other wireless video transmission module, connect it to the FPV HUB via HUB-VTX cable according to pins description of the HUB-VTX cable.

Collocation 2&3: iOSD mini/iOSD MARK II and video transmission module connected

1)It’s alternative to use iOSD mini or iOSD Mark II.
2)Stop the Micro switch at OSD position when iOSD is connected to the FPV HUB.
3)Please refer to Collocation1 to connect the wireless video transmission module.

Notes:
(1)If using the FPV HUB, the original 4-Pin cable and video cable on PHANTOM 2 will be spared, please remove and clear them out. Make sure the video cable is totally cleared without any copper wire left to prevent short circuit damage.
(2)All connection operations should be conducted when the intelligent battery is powered off.
(3)Check whether pins of the connectors on the FPV HUB are straight and in good condition before connecting. Pls plug and unplug the connector carefully to avoid damage or short circuit.
(4)It’s not recommended to install the FPV HUB and extended devices inside the PHANTOM 2 aircraft.
(5)Make sure to install the AVL58 away from the compass to avoid interference.
(6)FPV HUB is non water-proof, if it is wet, please wash it with alcoholic cleanser and dry it before use. Otherwise components may be damaged cause of electrochemical corrosion.
(7)Do not leak any metal, conductive objects into the connector pins of FPV HUB to prevent short circuit damage.
(8)It’s not recommended to use cables not in the kit to connect devices to avoid unexpected damage.
(9)Make sure the connection is correct when using non-DJI recommended wireless video transmission module.

Tips:
(1)FPV HUB has a resettable fuse for over circuit precaution. The fuse will automatically open if the working current of power consuming devices (except DJI Zenmuse series) goes over 2A or if VCC and GND short circuited to prevent damage. After the short circuit trouble issued or the over current load is removed, turn off the power of the intelligent battery, the fuse will recover after 10secs.
(2)A component will be damaged if PHANTOM 2 has been short circuit once. In this condition, users still can use the FPV HUB and make the PHANTOM 2 work well again, ignoring the damaged component.

PM  EMAIL  Attn:RR  Quote
01-13-2014 04:47 AM  3 years agoPost 6
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released new firmware for Zenmuse H3-2D!

What’s new?

Firmware

Optimized user experience when using the PHANTOM 2 remote controller for Zenmuse H3-2D pitch control.

Important notes for PHANTOM 2 users:

For users of the PHANTOM 2 with Zenmuse H3-2D, one must adhere to following steps to upgrade the remote controller firmware.

1)Use the PHANTOM RC Assistant software to upgrade the remote controller firmware to V1.0.1.11.
2)Calibrate the sticks and X1 channel of the remote controller using the PHANTOM RC Assistant software.
3)Use the PHANTOM 2 Assistant software to upgrade the Gimbal IMU firmware to V1.8 via Upgrade page.
4)After the upgrade is completed, calibrate the X1 channel of the main controller using the PHANTOM 2 Assistant software to ensure compatibility of PHANTOM 2 and the Zenmuse H3-2D.

Please click here for more information.

PM  EMAIL  Attn:RR  Quote
01-24-2014 12:09 PM  3 years agoPost 7
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released the FPV HUB, camera mounting​bracket and prop guard for Phantom 2!

PHANTOM 2 FPV HUB

In the kit:

FPV HUB, cables and instructions

Function:

Customized ports and cables for iOSD mini, iOSD Mark II or AVL58.

Feature:

FPV HUB’s integrated iOSD mini,iOSD Mark II or AVL58 ports,
connecting directly to the PHANTOM 2 central board and built-in
main controller through an 8-Pin cable. This simplifies connecting
these items and eliminates the need for soldering.

PHANTOM 2 Camera Mounting Bracket

In the kit:

Camera mounting bracket and screws

Function:

Attachment for GoPro cameras and others.

Feature:

Gimbal free camera attachment for GoPro and similar cameras.

PHANTOM 2 Prop Guard

In the kit:

4 prop guards and instructions

Function:

Fitted under the rotors to prevent damage to rotors or surroundings.

Feature:

Easy to attach, lightweight, safe and reliable.

Specifications:

Weight (Single): 21g
Angle: 150.0°
Radius: 128.25mm
Whole Size with Four Prop Guards: 613mm

Important Notes:

Make sure the PHANTOM 2 weighs no more than 1350g after
mounting prop guards. Any extra weight will compromise flight
capabilities causing a safety risk. The total weight of a PHANTOM 2
with H3-2D gimbal, iOSD and wireless video transmitter will be over
1300g, prop guards are not recommended for similarly equipped
PHANTOM 2s.

Please click here for more information.

PM  EMAIL  Attn:RR  Quote
02-10-2014 11:18 AM  3 years agoPost 8
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI Lightbridge - 2.4G Full HD Digital Video​Downlink

DJI Lightbridge will start shipping during February 2014. We will only have 500 units available this month so get your pre-orders in as soon as possible.

DJI Lightbridge is an all new revolutionary 2.4G Full HD digital video downlink. DJI Lightbridge offers extremely powerful equipment packed into a small and light-weight form factor. By offering 1920 x 1080p@30fps video data transmission from up to 1.7km (1.05miles) away, it's the ideal solution for the professional aerial photographer and FPV users. Set yourself free and remove the limits from low definition analog video transmitters.
[URL="

Watch at YouTube

Features:

2.4G Full HD Digital Video Downlink
-1920x1080@60fps input and 1920x1080@30fps output

Extreme Long Distance Transmission
-Less than 100mW ground unit transmission in full compliance with CE and FCC certification
-5dBi omni-directional antenna offers an enormous distance of up to 1.7 km (1.05 miles)
-Optional 14dBi patch antenna boosts transmission distance tremendously to 5km (3.1 miles)

Multiple Input And Output Connections
-AV input
-HDMI input
-DJI Zenmuse gimbal input (Digital Video/Power Supply/OSD Data)
-HDMI HD image output
-USB 2.0 image data output for iOS and Android phones and tablet synchronization

Built-in Remote Control Link
-Uplink remote control transmission and downlink video work simultaneously on 2.4GHz.
-Remote control data travels to the uplink via the TX-Thru Port at the same time that video is streamed back down all without interference.
-Support for two remote controls: one for flight control (10 Channels) and the other for gimbal control (6 Channels). Control signals are received in the air and then transmitted to the flight controller through D-BUS.
-When used with a non-2.4G radio transmitter, video only transmission operation is supported. The DJI 5.8G radio transmitter is recommended.

Strong Anti-Jamming Technology
-Frequency Hopping Spread Spectrum(FHSS) + Direct Sequence Spread System(DSSS) technology is used for uplink transmission to enhance stability and offer anti-jamming capability.
-MIMO multi-antenna technology and OFDM modulation methods along with advanced algorithms are utilized for downlink transmission to enhance data bandwidth, improving dynamic performance and increasing stability even in harsh environments.
-Channel interference is constantly monitored during downlink transmission with automatic switching between 8 channels for the best possible signal.
-Up to 8 downlinks can be connected for parallel streaming and work independently without interference.

Low Latency Transmission
Maximum latency of up to 80ms

Built-in OSD (On-Screen Display) Function
-No additional equipment required for OSD functions when used with A2/WooKong-M/Naza-M V2 flight controllers. Flight parameters will be displayed onscreen.
-OSD functionality can be turned off via mobile software for HDMI and iOS/Android Output.

Must Work With DJI Multi-Rotor Flight Controllers
-DJI A2, WooKong-M and Naza-M V2 flight controllers
-Phantom 2, with DJI 5.8G radio transmitter.

Multi-device Operation Mode, Stable and Reliable
-A single air unit can transmit to multiple ground units sending video to multiple screens. (Only one of the ground units can send a control signal while additional ground units will only be able to receive a video signal)
-Encryption ensures only authorized devices can receive data which can be programmed via mobile device software.

Built-in High Capacity Battery
-Ground unit has a built in high capacity 4000mA battery offering up to 4.5hours of use per charge.
-Rechargeable through the supplied charger or via a 3S~6S Li-Po power battery.A full charge takes approximately 1.5 hours.
-LED battery level indicator
-Also functions as a USB charger for mobile devices prolonging the life of peripheral equipment.

Electromagnetic Interference Shielded Structural Design
-Aluminum alloy casing
-Extreme internal and external shielding for interference protection.

PM  EMAIL  Attn:RR  Quote
02-21-2014 01:48 PM  3 years agoPost 9
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released the car charger for Phantom 2!

DJI Phantom 2 car charger has been released to provide outdoor charging solutions for the Phantom 2 battery.

Phantom 2 Car Charger:

In the kit:
Car charger and instructions

Function:

Used to charge the Phantom 2 in-car or through 3S-6S Li-Po batteries.

Feature:

Convenient, practical outdoor charging solutions for the Phantom 2 battery.

Note:

FPV Hub Kit Instruction V1.1 has added description of using FPV Hub to connect the H3-2D gimbal, GCU and other devices on non-Phantom 2 flight platforms.

Please click here for more information.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 3739 views
Scorpion Power Scorpion Power
Helicopter
e-
DJI Innovations
 News  DJI PHANTOM 2 Launched!
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Saturday, November 25 - 11:40 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online