RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 652 views POST REPLY
Helicopter
e-
Miniature Aircraft Whiplash & Furion 6
› HELP!! Servo Linkages on furion 6...
11-04-2013 09:20 PM  4 years agoPost 1
Island Heli MKK

rrNovice

Kaunakakai, Molokai, Hawaii,

My Posts: All  Forum  Topic

Anyone with furion 6 fbl...

HELP!!!! I trying to set up & center my swash plate.
Like 90.Deg. I did, But when i flip to IdleUp & Normal mode move the swash around. Seem like the swash is a little near to FBL rotor head & swash arms not look close to 90.Deg.

By the the Manual said!!!Use Sizes Below.

I'm using linkage size. to servo to swash is about: 21mm X3 center link to link.
And Inner-ring swash to pitch arms. I using 48mm X2 center link to link. Using 11.deg pitch.

If Anyone has a better linkage sizes to make it on the Dot 90 Deg. Center stick. And not close to head. & still use 11.Deg & up.
Pitch.

Will be much Mahalos & Aloha for your help!!!! Keep flying
( Like my X-CELL Furion 6 )

( Island Heli MKK) furion 6 FBL ,flying wing naptune EDF..

PM  EMAIL  GALLERY  Attn:RR  Quote
11-04-2013 09:41 PM  4 years agoPost 2
JKos

rrProfessor

Redondo Beach, CA

My Posts: All  Forum  Topic

Ok,
1) Achieve exactly 50% pitch on your transmitter. I make the middle three points 50% so that if the stick is near the middle, it is definitely at 50%.

2) Center your servo arms. Make them 90 degs. Do you have the carbon fiber aid that comes with the Furion kit for getting the outside servos perfect? This would be mechanicaly first, if possible, through servo arm selection then through whatever adjusting means your chosen FBL unit uses.

3) Adjust the links between the servo arms and the swash to center the swash in its up and down travel.

4) Adjust the links from the swash to the blade grips to achieve zero pitch on the blades.

There you go. The lengths listed in the manual are merely starting points. Don't forget to put your pitch curve back the way you want it.

- John

RR rules!

PM  EMAIL  GALLERY  Attn:RR  Quote
11-05-2013 02:06 AM  4 years agoPost 3
Island Heli MKK

rrNovice

Kaunakakai, Molokai, Hawaii,

My Posts: All  Forum  Topic

Mahalo John!!!
For the info!!!

Anyone else??? To confirm?

Just wondering Tail servo. What hole on servo arm you guys use?
Manual says, Around 13-15mm to center screw servo. I use 14mm to center...

Again Mahalo Thanks Alot!!!!
Joel,

( Island Heli MKK) furion 6 FBL ,flying wing naptune EDF..

PM  EMAIL  GALLERY  Attn:RR  Quote
11-05-2013 05:55 PM  4 years agoPost 4
Scott1115

rrElite Veteran

Greenwich, CT

My Posts: All  Forum  Topic

+1 JKos

Exactly what I do. The manuals' numbers are close, but just a guide.

Compass 7HV, Trex 550E
RCRCC

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 652 views POST REPLY
Helicopter
e-
Miniature Aircraft Whiplash & Furion 6
› HELP!! Servo Linkages on furion 6...
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Wednesday, May 23 - 11:44 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online