RunRyder RC
 4  Topic Subscribe
WATCH
 1 page 868 views POST REPLY
HelicopterRadio - Futaba FASST › FUTABA 750 GYRO INTER ACTION ON CYCLIC
10-10-2013 10:25 AM  4 years agoPost 1
gary saia

rrApprentice

chandler tx usa

My Posts: All  Forum  Topic

Hi futaba guru's , I have gottem my750 CGY set up with the 4 point ccpm , works perfect , then i let a friend from longview tx that has been flying the 750 , i asked him to help hooking up my gv-1 governor with my Futaba 14 sg radio, after he played with it , I notice it was a nightmare , up and down collective with swash cyclic inter action all over the place , orginallly i had it working fine , , so i got it back and went thru the entire menus resetting all values to stock , first off He changed s.bus basic map channels selection , so i put it back to stock assigments like in the manual , channels 1-8 , FIRST OFF THERE ARE NO MIXING OF CHANNELS IN MY 14 SG , I WENT THRU THE ENTIRE RADIO , ALSO I AM RUNNING A FLY BAR HEAD AND ACCORDING TO BEN MINOR , I SET ALL GYRO CYCLIC CONDITIONS TO NORMAL , AND REDUCE GAIN TO 0 gain , that is fine , , I GOT JUST ABOUT ALL IT WORKING PROPERLY , EXCEPT 1 THING , I GET A LITTLE LEFT AILERON CONTROL ONLY BACK CYCLIC ONLY , I GOT FORWARD , NO OTHER MOVEMENT, WHEN I GIVE LEFT OR RIGHT AILERON , NO FOR AND AFT MOVEMENT , ,,,, JUST ON BACK CYCLIC , WEIRD , ANY HELP, I AM PLANNING ON GOING THRU EVERY MENU AND RECHECK BEFORE I PULL OUT THE REST OF MY HAIR , GARY SAIA TEXAS , 817-812-7050, E-MAIL IS garyvsaia@gmail.com

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
10-10-2013 12:25 PM  4 years agoPost 2
gary saia

rrApprentice

chandler tx usa

My Posts: All  Forum  Topic

fix it
all my friends , Uh !!

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-10-2013 03:27 AM  4 years agoPost 3
wc_wickedclown (RIP)

rrProfessor

long beach calif

My Posts: All  Forum  Topic

interaction most of the time from the elevator

relocate elevator linkage 1 hole up or back

Insha Allah made in america

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-10-2013 10:54 AM  4 years agoPost 4
Kloss08

rrApprentice

Bradford PA USA

My Posts: All  Forum  Topic

Does it perform this same issue on other models? You said your model has a flybar. Do you have the cyclic servos plugged in to the Cgy 750 or to the receiver.

Team Futaba
Team Pulse Batteries
Enjoy it today

PM  EMAIL  GALLERY  Attn:RR  Quote
11-11-2013 03:35 AM  4 years agoPost 5
Chris.C

rrVeteran

Hong Kong

My Posts: All  Forum  Topic

If yours have a flybar and not intend to use cyclic gyros in the 750(gain set to zero as you said), then I would use a 8 channel receiver, e.g. a 6208SB, plug the pitch, ele and ail servos directly into the receiver, 750 is just for the rudder gyro.

This way, I can set 14SG into whatever suits your swash plate other than H-1. You will have the "Swash" menu back and mix out interaction from there.

PM  EMAIL  GALLERY  Attn:RR  Quote
11-12-2013 01:57 AM  4 years agoPost 6
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

That will work. The same mixers are in the 750 if he would like to preserve full S.Bus implementation.

Ben Minor

Team Futaba Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 868 views POST REPLY
HelicopterRadio - Futaba FASST › FUTABA 750 GYRO INTER ACTION ON CYCLIC
 Print TOPIC  Make Suggestion 

 4  Topic Subscribe

Sunday, April 22 - 1:00 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online