RunRyder RC
 3  Topic Subscribe
WATCH
 1 page 693 views POST REPLY
Scorpion Power Scorpion Power
HelicopterEngines Plugs Mufflers Fuel › Permatex High-Temp RTV to glue in a clutch liner - OK?
01-24-2013 05:22 PM  4 years agoPost 1
ticedoff8

rrKey Veteran

Morgan Hill, CA. USA

My Posts: All  Forum  Topic

I normally use JB Weld to glue in my clutch liners.
I've never had a problem with delimitation and the liner stays secure the life of the liner.
But, when I use the JB Weld, it takes about an hour to clean out the clutch bell and be ready to glue a new liner. The clean out takes lots of heat, scrapping, Dremeling and clean-up.

I am trying something new - Permatex High-Temp RTV Silicone Gasket Maker (orange color).

I already installed the liner. It went in okay and cleaned up nice. But I haven't flown it yet.

This is a Raptor 90 with a YS 91SR-3DS - so there is some strain on the liner / glue.

A new OEM bell comes with the liner pre-installed and they use a thin blue glue of some kind. It lasts the life of the liner and cleans out easy when replacing it. But, I have no idea what it actually is.

Has anyone used the Permatex High-Temp RTV Silicone Gasket Maker when replacing a clutch liner?
Did I make a big mistake here?

I would rather pull out the new liner and replace it with another using JB Weld than fly it as is and have something weird happen with the Permatex.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-25-2013 02:49 AM  4 years agoPost 2
John Krebs

rrVeteran

Pittsburgh, PA

My Posts: All  Forum  Topic

I don't think it would be strong enough. I've used JB weld but now use 5 min epoxy. I know some guys that use slow set super glue.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-25-2013 03:20 AM  4 years agoPost 3
fastflyer20

rrKey Veteran

N. Tonawanda, NY

My Posts: All  Forum  Topic

JB Weld is very heat resistant and hard to remove plus it is very thick causing the liner to not always conform to the bell.

Any of the common epoxies (5, 15, 30 minute) remove easily with heat and require very little additional clean up. These are the simplest glues I have found to use on liners both on install and removal.

It may work, but RTV would not be my first choice.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-25-2013 05:58 AM  4 years agoPost 4
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

30 minute epoxy is the way to go. Plenty of time to get it installed, holds well, easy to remove when needed. Juat about anything else is overkill.

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
01-25-2013 06:24 AM  4 years agoPost 5
BladeStrikes

rrElite Veteran

Shelby TWP,Mi

My Posts: All  Forum  Topic

I tried JB-Weld and 30 minute epoxy,JB-Weld works MUCH better..If you put a tiny coat on the inside of the clutch bell with your finger,you won't have issues like others have and its very easy to remove.Takes a whole 3-4 mins to remove the old liner and JB-Weld.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-25-2013 01:56 PM  4 years agoPost 6
reddragon

rrElite Veteran

Brooklyn, N.Y.

My Posts: All  Forum  Topic

The Permatex will not hold the clutch liner. JB Weld or Epoxy will work best.

Wayne - Fly it like you stole it! You're in good hands with Runryder!

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 693 views POST REPLY
Scorpion Power Scorpion Power
HelicopterEngines Plugs Mufflers Fuel › Permatex High-Temp RTV to glue in a clutch liner - OK?
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Thursday, October 19 - 12:51 am - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online