RunRyder RC
 4  Topic Subscribe
WATCH
 1 page 837 views POST REPLY
Scorpion Power Scorpion Power
HelicopterRadio - Futaba FASST › Program question on T18 (or T14)
01-21-2013 06:43 PM  4 years agoPost 1
filou406

rrApprentice

Lexington SC US

My Posts: All  Forum  Topic

Hi
I would like to program a function but not sure that it is possible on the MZ.
I need a channel which goes from -100% to +100% when I push the SH switch (2 positions mom) and then each time I push it the channel will have to switch from one limit to the other (like an hysteresis function ?)
Thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
01-22-2013 04:40 AM  4 years agoPost 2
brey

rrApprentice

staples MN

My Posts: All  Forum  Topic

If you use ALT instead of normal where you pick the switch on position then every time you pull on the switch it will turn it on then pull it again and will shut it off. I think that is what you are looking for?

What are you using this mix for? Or is it not a mix?

PM  EMAIL  GALLERY  Attn:RR  Quote
01-22-2013 05:21 AM  4 years agoPost 3
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

Please rephrase the second part of your requirement description.

"Not possible" is rarely used to describe anything with an MZ, so I would think there is at least way to skin your cat. I do need a better explanation of what you want to do, though.

Ben Minor

Team Synergy Team Futaba Team Kontronik USA
Progressive RC

PM  EMAIL  GALLERY  Attn:RR  Quote
01-22-2013 10:14 AM  4 years agoPost 4
modtron

rrKey Veteran

Oxford. UK

My Posts: All  Forum  Topic

This action was available on the 9ZAP series.

It can be set up exactly the same way on both the 14 & 18MZ's but the function does not work.

Hoping Futaba will correct this at some time ?

modtron
Oxford UK

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-22-2013 12:38 PM  4 years agoPost 5
filou406

rrApprentice

Lexington SC US

My Posts: All  Forum  Topic

Hello
This for my quadri when I fly FPV. The OSD (flight information) has 5 pages. To switch from one to another, the channel signal has to go from one limit to the other and it is like a loop (value -100 = Page 1, value +100 = page 2....). Instead of using a normal switch that I will never know in which position it is (depends on the last use but not linked to the current page) I would like to change the page each time I push the mom switch.

Brey, I did not find the ALT command in the switch screen..

Thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
01-22-2013 12:56 PM  4 years agoPost 6
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

I think I know how to do it with a work around. Let me see if I can configure a set up for you one night this week.

Ben Minor

Team Synergy Team Futaba Team Kontronik USA
Progressive RC

PM  EMAIL  GALLERY  Attn:RR  Quote
01-22-2013 01:04 PM  4 years agoPost 7
filou406

rrApprentice

Lexington SC US

My Posts: All  Forum  Topic

Ok thanks !

PM  EMAIL  GALLERY  Attn:RR  Quote
01-22-2013 02:04 PM  4 years agoPost 8
Skaluf

rrVeteran

Champaign, IL

My Posts: All  Forum  Topic

I worked on this one for a bit yesterday myself. Now that I have more information I'll give it another shot. Like Ben said, there is not much that the MZ cannot do. It just takes some thought to figure out how to make it happen.

Steve

Steve Kaluf
Hobbico

PM  EMAIL  GALLERY  Attn:RR  Quote
01-23-2013 01:40 AM  4 years agoPost 9
brey

rrApprentice

staples MN

My Posts: All  Forum  Topic

Brey, I did not find the ALT command in the switch screen..
If you went to (system) then (switch), it's not in there.

Too find the ALT mode go to (model menu) then (Prog. Mixes) then click on program mix 10. In the upper left corner right under where it says Mixes. It will say on Click on (on) then on (on) again then pick switch (sh) then click on (on Pos.) In this screen is where you can pick ALT mode. Where it says (NORM) click on that and it will switch to ALT..
That's where to find ALT but not what you need though.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-28-2013 04:03 PM  4 years agoPost 10
filou406

rrApprentice

Lexington SC US

My Posts: All  Forum  Topic

Hi,
Did you have some time to work on this question because I tried different way but nothing works ?
Thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 837 views POST REPLY
Scorpion Power Scorpion Power
HelicopterRadio - Futaba FASST › Program question on T18 (or T14)
 Print TOPIC  Make Suggestion 

 4  Topic Subscribe

Monday, October 23 - 8:07 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online