RunRyder RC
 5  Topic Subscribe
WATCH
 1 page 940 views POST REPLY
Helicopter
e-
Mikado
Logo 600 › Logo 600 sx violent tail hunting
01-07-2013 02:14 AM  5 years agoPost 1
johnnie eagle

rrApprentice

Florham Park, NJ 07932

My Posts: All  Forum  Topic

Logo 600 3d upgraded to sx. Heli started to hunt during funnels the last few weeks. This was a new development. I figured I was going to upgrade so I figured I would wait . Did the full upgrade, tail,head,main shaft and third bearing . I have always run edge 105's. now it's worse. It does it on high g turns also. Jr 8900g servo, 2000 HS.
Any suggestions or should I try 95mm blades first and if still a problem look at the servo.

Team Minicopter - Peak Aircraft, Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 02:16 AM  5 years agoPost 2
wrongler

rrProfessor

Brewerton, New York

My Posts: All  Forum  Topic

Is there a static kit installed?

Bill Whittaker

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 02:18 AM  5 years agoPost 3
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

Tail thrust bearings going bad? Or maybe not seated properly?

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 02:21 AM  5 years agoPost 4
johnnie eagle

rrApprentice

Florham Park, NJ 07932

My Posts: All  Forum  Topic

600 tail
Yes the static kit is installed and I just rebuilt the tail with the sx upgrade and the thrust bearings are in correctly and the tail is smooth as silk.

Team Minicopter - Peak Aircraft, Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 02:40 AM  5 years agoPost 5
ToddM

rrNovice

USA

My Posts: All  Forum  Topic

John- Curious what you find. I'm in the middle of upgrading a new 6003D to SX now, including the new beefy tail. Todd






Logo 690SX SAB 570

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 02:58 PM  5 years agoPost 6
Anton123

rrApprentice

Canada

My Posts: All  Forum  Topic

Have you tried a different horn on the servo?

PM  EMAIL  Attn:RR  Quote
01-07-2013 04:12 PM  5 years agoPost 7
johnnie eagle

rrApprentice

Florham Park, NJ 07932

My Posts: All  Forum  Topic

tail
I have a Mikado horn on the servo. Its new.

Team Minicopter - Peak Aircraft, Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 07:24 PM  5 years agoPost 8
SGrim80

rrVeteran

Lehigh Valley, PA

My Posts: All  Forum  Topic

Do you hear any loud or strange noises? Maybe your tail blade pitch is causing the tail blades to stall?

Mikado USA
Team Scorpion!

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 08:30 PM  5 years agoPost 9
VANHELI

rrVeteran

Omaha,Nebraska

My Posts: All  Forum  Topic

...maybe check the continuity of the static kit.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 09:44 PM  5 years agoPost 10
johnnie eagle

rrApprentice

Florham Park, NJ 07932

My Posts: All  Forum  Topic

I'll do that

Team Minicopter - Peak Aircraft, Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 10:09 PM  5 years agoPost 11
Anton123

rrApprentice

Canada

My Posts: All  Forum  Topic

I had the same Mik horn... After changing it to a reg futaba horn as it was closer to center..Adjusted the gain.. Issue was gone.. Or maybe an adjustment on the push-rod has to be made..as the distance may have changed from the upgrade..? Hope this helps!

PM  EMAIL  Attn:RR  Quote
01-07-2013 11:16 PM  5 years agoPost 12
raildog

rrApprentice

albuquerque nm

My Posts: All  Forum  Topic

Check ur tail bearings to be sure they are smooth..

PM  EMAIL  GALLERY  Attn:RR  Quote
01-08-2013 11:04 AM  5 years agoPost 13
HeliKopter Ken

rrKey Veteran

Gray, LA

My Posts: All  Forum  Topic

I found my ball loose on my tail rotor slider. Tail holds a little better now. I could feel a very small amount of play in the tail linkage by hand. I had to remove hud to actually find that it was loose. Reassembled tail and everything was perfect.

Good luck.

Aurora, Raptor 90 FBL, Logo 600SX

PM  EMAIL  GALLERY  Attn:RR  Quote
01-08-2013 12:29 PM  5 years agoPost 14
ToddM

rrNovice

USA

My Posts: All  Forum  Topic

Do you have any play in the grip arms? When I was assembling the new SX tail rotor upgrade, I noticed a tiny bit of literal play in the grip arms one tightened down. I've read that this is normal and won't effect flight.






Logo 690SX SAB 570

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 940 views POST REPLY
Helicopter
e-
Mikado
Logo 600 › Logo 600 sx violent tail hunting
 Print TOPIC  Make Suggestion 

 5  Topic Subscribe

Sunday, April 22 - 5:32 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online