RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 1133 views POST REPLY
Helicopter
e-
Electric Battery-Charger-pSupply
› Help with Thunder Power 1010c lipo charger
06-08-2012 01:14 AM  5 years agoPost 1
hce111

rrNovice

Chagrin Falls, Ohio USA

My Posts: All  Forum  Topic

Can anybody give me the sequence steps to using TP 1010C charger, i searched you-tube but haven't found anything I do have a balance adapter but directions are kind of vague? I do want to balance charge I am charging 6s 2600 and 2700 packs. I do understand the c factor (etc) with lipos.
So I plug the two balance plugs start with bigger one first and the smaller one, then I plug the deans plug in, from there i hit the select button, check makes sure I am charging a 6s pack check my charge rate 3.0 amps where do I go from here? do I tab to reading balance info and hit start on the adapter? or do I start the charge process next! I hope I made some sense here I just want to make sure i don't burn up a lipo I had a teamenegy balance charger before but it was having a had time harging the bigger packs since it only had a 50 watt output.I would appreciate any info on the procedure.
THANK YOU!!

AMA # 986520

PM  EMAIL  Attn:RR  Quote
06-11-2012 03:28 AM  5 years agoPost 2
yellow303

rrNovice

Verona, mo

My Posts: All  Forum  Topic

I have the same charger but never used it but heree is a link to the manual for tat charger, hope that helps!

[http://www.rctoys.com/pdf/TP1010C-Charger.pdf]

Good luck,
Yellow303

PM  EMAIL  GALLERY  Attn:RR  Quote
06-11-2012 04:47 AM  5 years agoPost 3
Chuck Bole

rrElite Veteran

Tulsa Ok. U.S.A.

My Posts: All  Forum  Topic

You are using the TP 210 balancer w/ the cable to the 1010 charger right? I don't have one to look at so going from memory.
Set the charger to the correct cell count

Set the charge rate (Amps)

Connect the balance leads to the 210 balancer
( one end is marked group A the other end is marked group B. One end has 2 6pin connectors the other end has a 6pin and a 4pin connector)
Use the end with the 6 and 4 pin connector for your 6S pack.

Connect the main power lead

Push start and hold till the charger beeps, it'll check cell count ect. Then it will start the charge. Pushing either the + or - button
after the charge has started will show the voltage of each cell connected to the balancer.

As best i can remember..

chuck

Here is a link to the balancer directions also..
http://www.rctoys.com/pdf/thunder-p...user-manual.pdf

And
http://www.rctoys.com/pdf/thunder-p...user-manual.pdf

Team Synergy Field Representative / Thunder Power

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-12-2012 12:31 PM  5 years agoPost 4
hce111

rrNovice

Chagrin Falls, Ohio USA

My Posts: All  Forum  Topic

Thanks for the information.

AMA # 986520

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 1133 views POST REPLY
Helicopter
e-
Electric Battery-Charger-pSupply
› Help with Thunder Power 1010c lipo charger
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Friday, May 25 - 8:08 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online