RunRyder RC
 5  Topic Subscribe
WATCH
 1 page 1953 views POST REPLY
ProModeler Scorpion Power
HelicopterHIROBOHirobo Turbulence › My settings for CGY750 on a FBL D3
09-06-2011 08:08 AM  5 years agoPost 1
gornElite Veteran - Western Australia - My Posts: All  Forum  Topic

Hi Guys
The following settings are what I have dialled in to my CGY750, on my FBL Dominik D3.
These settings are working with the stock D3 head, converted to FBL.
I have the new SSL head, but am waiting on new stocks of 690mm blades before I switch over, as the new head is wider.

Before I get started, I will list equipment used, for a baseline.

D3 EX
Converted head using Mikado washout base and arms, and D3 seesaw balls.
Cyclic servos: Futaba BLS253
Tail servo: Futaba BLS251
Throttle servo: Futaba 9252
Voltage reg: Dualsky VR8L at 6v
Servo horn hole spacing from center: 12.5mm
Receiver: Futaba R6108SB
Flybarless system: Futaba CGY750 (sensor is top mounted, with lead facing to the rear)

Settings will only be shown if I have changed them from default, or if I think it was of interest to anyone doing the same.

RUDDER BASIC
Servo: 760
GY.DR: reverse
Sv.Limit A: 100
Sv.Limit B: 117
FLT. Mode: 3D

RUDDER EXPERT
F/F.Rate L: +20%
F/F. Rate H: +20%
Sens Mode: Moderate

AIL BASIC
Ail Dir: Rev
AGN: 82% Gm:A90%
Same for Normal mode
Work Mode: CMT

AIL EXP
AVCS DMP: 100%
ANG Rate: 125%
Sen Mode: Middle

ELE BASIC
Ele Dir: Norm
All other settings are the same as Ail

SWASH BASIC
Type: H3-140
Servo: 1520
Size: 600-700
Flt Mode: 4
Ail.Rev:Normal
Ele.Rev: Reverse
Pit.Rev: Reverse
Ail.Ntr: 0
Ele.Ntr: +30
Pit.Ntr: -23
Ail and Ele Rate: 60%
Pit Rate: 40

SWASH EXP
Phase Equ: OFF
Rot Equ: ON
Equ.Dir: Normal

GOV BASIC
RPM Set1:1800
RPM Set2: 1900
RPM Set 3: 2050
Gear Ratio:8.25
Servo Type: 1520
Yaw.Comp: CW/Top

GOV EXP
Wrk.Mode: Governor
Response: Middle
GV.Gain: 45%
Llmt.Hov: 25%
Llmt.Idup: 45%

My radio is a Futaba 10CHG

Settings:
Only listed where changes made, or if relevent to each individual setup.
IE: I will not show trim flight subtrim settings, as these will not work for you.

REVERSE:
Elevator
Throttle

Aux-Ch Select
CH5: SwF
CH6:----
CH7: SwC
CH8: SwD
CH9: SwB POSI: UP
CH10: SwB POSI: UP

Parameter
Swash: H1

THROTTLE CURVE
Norm: Linear
ID1: 100,75,70,65,70,75,100
ID2: 100,82,75,75,75,82,100

PITCH CURVE
Norm:-18,-18,-18,0,+25,+50,+100
Id and 2 are linear
Hold: Linear

GYRO SENSE
Mix: ACT
Mode: GY
SW: Cond

Rate:
Norm: AVC 80
IDL1: AVC 80
IDL2: AVC 80
Hold: AVC 85

GOVERNOR
Mix: ACT
UP: 0%
CTR: 50%
DWN: 100%
SW: E
cut CH: +CH7

CONDITION SELECT
Idle-Up 1: E: Center
Idle-Up 2: E: Down
Idle-Up 3: INH
THR-Hold: C: CTR and DWN

Thats about it.
Hope some of you find this helpful, as its painful to sit here typing it


For the love of the hobby

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
09-06-2011 07:00 PM  5 years agoPost 2
ttrip06

Senior Heliman

Central Pa

My Posts: All  Forum  Topic

Thanks.

Tim Tripoli

Team Futaba, Rail Blades
Team Crash
ProggressiveRC

PM  EMAIL  GALLERY  Attn:RR
10-12-2011 10:05 PM  5 years agoPost 3
per-åke

Heliman

Sweden

My Posts: All  Forum  Topic

settings for CGY750 on a FBL D3

Hi
what (Mikado washout base and arms) do you use to build your Hirobo D3
to FBL do have any part.number for the washout base and arms
Per-Åke Winberg

PM  EMAIL  Attn:RR
10-12-2011 10:06 PM  5 years agoPost 4
tracknoob

Senior Heliman

Miami Florida

My Posts: All  Forum  Topic

Good looking bird, thanks for taking the time to do that!

I will be setting up my own 750 in a couple of weeks, so it's good to see some folks posting who have already been through it.

PM  EMAIL  GALLERY  Attn:RR
10-13-2011 09:22 AM  5 years agoPost 5
gorn

Elite Veteran

Western Australia

My Posts: All  Forum  Topic

The washout base complete assembly is MIK4018.
You will be able to find that from any Mikado agent around the world.
Fits perfectly.

Tracknoob
My pleasure

For the love of the hobby

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
10-13-2011 12:12 PM  5 years agoPost 6
kiksko

Senior Heliman

San Lorenzo, CA

My Posts: All  Forum  Topic

nice heli gorn

PM  EMAIL  GALLERY  Attn:RR
10-13-2011 12:36 PM  5 years agoPost 7
gorn

Elite Veteran

Western Australia

My Posts: All  Forum  Topic

Thankyou

For the love of the hobby

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
WATCH
 1 page 1953 views POST REPLY
ProModeler Scorpion Power
HelicopterHIROBOHirobo Turbulence › My settings for CGY750 on a FBL D3
 Print TOPIC  Make Suggestion 

 5  Topic Subscribe

Saturday, August 19 - 5:48 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online