RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 571 views POST REPLY
HelicopterRadio - Spektrum DSM › AR7100r - GEAR port
08-01-2011 07:32 PM  6 years agoPost 1
praztek

rrApprentice

brandon , fl

My Posts: All  Forum  Topic

When creating a new model in my Dx7 “ all settings left as default “, is the Gear port on the receiver delivering any power.

If not, which setting on the Dx7 should I change to enable this?

Thank You

PM  EMAIL  GALLERY  Attn:RR  Quote
08-01-2011 07:53 PM  6 years agoPost 2
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

I could be wrong because my 7100 is still on a brown truck, but most servo outputs have power all the time via the power bus.

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
08-01-2011 07:57 PM  6 years agoPost 3
praztek

rrApprentice

brandon , fl

My Posts: All  Forum  Topic

Based off the manual.

Looks like I have to set the Gear channel to AUX in order to enable it.

To Select the Function for the Gear Channel

Press the DOWN and SELECT keys simultaneously, then turn on the transmitter.

Press the UP or DOWN key until INPUT SELECT appears on screen.

Press the SELECT key until GEAR is highlighted.

Press the INCREASE or DECREASE key to select the desired function.

The gear channel options are:

INH:

Inhibit is selected if the gyro function will not be used on the gear channel. Selecting inhibit turns off the gear

channel, allowing it to be used as a slave channel for mixing.

GEAR:

Gear is selected if the gyro gain or retractable gear position is to be selected using the gear switch.

GYRO:

Gyro is selected under gear if you wish to have the Gyro Sensing (Page 91) operate using the

gear channel.

AUX2:

The Auxiliary 2 switch is used to activate the gear channel.

PM  EMAIL  GALLERY  Attn:RR  Quote
08-01-2011 08:26 PM  6 years agoPost 4
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

I said I was guessing

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
08-01-2011 08:55 PM  6 years agoPost 5
praztek

rrApprentice

brandon , fl

My Posts: All  Forum  Topic

I might be guessing as well, just recalled that there was not a satellite attached. I'm not home right now, but not sure if this would cause No output power from the connections. I'll find out later this evening.

" Note: In order for the system to operate, one remote receiver must be plugged into receiver port B or R."

PM  EMAIL  GALLERY  Attn:RR  Quote
08-01-2011 09:07 PM  6 years agoPost 6
cbflys

rrVeteran

Nesconset, NY - USA

My Posts: All  Forum  Topic

The RX's power bus always delivers power when powered on - the signal however will not be there until the TX and RX link.

PM  EMAIL  GALLERY  Attn:RR  Quote
08-01-2011 09:09 PM  6 years agoPost 7
praztek

rrApprentice

brandon , fl

My Posts: All  Forum  Topic

Thank You.

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 571 views POST REPLY
HelicopterRadio - Spektrum DSM › AR7100r - GEAR port
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Sunday, April 22 - 9:46 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online