RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 423 views POST REPLY
HelicopterMain Discussion › binding ?
01-15-2011 06:48 PM  7 years agoPost 1
ROGER543

rrVeteran

bristol ct usa

My Posts: All  Forum  Topic

i am trying to bind my radio dx7 and when i bound it it did the blinking light at first then went to solid tried everything works fine shut it down and went to power it back up and everything works but i get a blinking light if that normal?? the reciever is a 6200 thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
01-15-2011 06:56 PM  7 years agoPost 2
cwright

rrKey Veteran

Blossvale New York

My Posts: All  Forum  Topic

If you didn't turn the transmitter off when you cycled the receiver that is normal. If you did cycle the transmitter and it is flashing make sure you removed the bind plug. Chuck

PM  EMAIL  GALLERY  Attn:RR  Quote
01-15-2011 07:23 PM  7 years agoPost 3
Steff Giguere

rrProfessor

St-Eustache, Quebec, Canada

My Posts: All  Forum  Topic

+1 on what CWright said

Team Synergy, Rail blades, Team Scorpion, V-Team

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-15-2011 07:34 PM  7 years agoPost 4
Bob Wales (RIP)

rrKey Veteran

Lebanon CT

My Posts: All  Forum  Topic

Roger turn off your transmitter and remove bind plug and turn power on on your tx then power on your reciever sould be fine.

PM  EMAIL  GALLERY  Attn:RR  Quote
01-15-2011 09:48 PM  7 years agoPost 5
helismash

rrKey Veteran

Gloversville, NY - Fulton

My Posts: All  Forum  Topic

If you don't turn off the TX snd cycle the power on the RX, the RX will flash indicating a loss of power. This is what it is supposed to do.

Hey, Who put the ground there!
T-Rex 500/T-Rex 600N FBL/T-Rex 600E PRO/T-Rex 700N/T-Rex 700FBL

PM  EMAIL  GALLERY  Attn:RR  Quote
01-15-2011 09:56 PM  7 years agoPost 6
ROGER543

rrVeteran

bristol ct usa

My Posts: All  Forum  Topic

everything works fine except the reciever light flashes and all my other reciever stays solid. don't want to take it out and crash it on it's first flight thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
01-15-2011 10:18 PM  7 years agoPost 7
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

When binding, make sure ALL receivers -- the main and the satellites -- stop blinking and go on solid before you turn things off.

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
01-16-2011 12:12 AM  7 years agoPost 8
ROGER543

rrVeteran

bristol ct usa

My Posts: All  Forum  Topic

thanks don't know what i did but was putting everything away inside the frame and now i get a solid light will go through it again

PM  EMAIL  GALLERY  Attn:RR  Quote
01-16-2011 01:44 AM  7 years agoPost 9
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

Double-check the cable that goes between the main receiver and the satellite. Make certain that both ends are fully seated in their connectors.

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 423 views POST REPLY
HelicopterMain Discussion › binding ?
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Monday, January 22 - 4:37 pm - Copyright © 2000-2017 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online